01
Nordberg C Series
Jaw crusher series
Installation identification for C80, C96, C106, C117, C120, C130, C150, C160, C200 and C3054.
Open the C Series page →Metso Jaw Crusher Series and Installed Models
Find jaw plates, cheek plates, mechanical parts, confirmed plate references and dedicated lifting tools by Nordberg C Series model.
OEM Equipment Category
Find Metso Jaw Crusher Details on the C Series Page
This page brings together Metso jaw crushers. The C Series page provides key specifications for ten standard and installed models, jaw plate references, mechanical spare parts and dedicated lifting tools.
1Main Product Family
10Listed and installed models
6Wear-part categories
6Mechanical spare-part categories
Series Directory
Dedicated Nordberg C Series Equipment Page
Review models, feed openings, power, jaw tooth profiles, confirmed plate numbers, mechanical parts such as eccentric shafts and bearings, and lifting tools.
Model Overview
Nordberg C Series Models and Feed Openings
Models and feed openings support installation identification. Jaw plates, cheek plates and structural parts still require serial numbers, tooth profiles, drawing and revisions.
| Model | Feed opening | Estimated maximum feed size | Motor Power |
|---|---|---|---|
| C80 | 800 × 510 mm | 410 mm | 75 kW |
| C96 | 930 × 580 mm | 460 mm | 90 kW |
| C106 | 1060 × 700 mm | 560 mm | 110 kW |
| C117 | 1150 × 760 mm | 610 mm | 132 kW |
| C120 | 1200 × 870 mm | 700 mm | 160 kW |
| C130 | 1300 × 1000 mm | 800 mm | 185 kW |
| C150 | 1400 × 1200 mm | 960 mm | 200 kW |
| C160 | 1600 × 1200 mm | 960 mm | 250 kW |
| C200 | 2000 × 1500 mm | 1200 mm | 400 kW |
| C3054 | 1380 × 760 mm | 610 mm | 160 kW |
Confirmed jaw plate references: Find jaw plate references by model, tooth profile and movable/fixed side; View dedicated C Series lifting tools.
Metso
Component Location Diagram
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Fixed jaw die | Fixed crushing face on left | Nordberg C Series |
| 2 | Movable jaw die | Movable crushing face on right | Nordberg C Series |
| 3 | Cheek plate | Side wall between jaw dies | Nordberg C Series |
| 4 | Spherical roller bearing | Cutaway bearing at upper shaft end | Nordberg C Series |
| 5 | Flywheel | Upper rear flywheel | Nordberg C Series |
| 6 | Adjustment wedge | Adjustment wedge behind lower movable jaw | Nordberg C Series |
Wear Parts
Crushing Chamber Jaw Plates and Frame Protection
Open general part pages by installation position, then match tooth profile, material and wear duty to the specific C Series machine.
01
Fixed Jaw Plates
Fixed Jaw Die
Mount on the frame side to form the crushing chamber. Tooth peaks, valleys and the heavily loaded lower zone experience impact and abrasion. Check one/two-piece construction, tooth profile and clamping arrangement.
View General Parts and Applicable Materials →
02
Movable Jaw Plate
Movable / Swing Jaw Die
Move with the pitman and apply crushing loads, combining impact, compression and sliding wear. Check tooth profile, weight, holes and seating against the pitman.
View General Parts and Applicable Materials →
03
Upper Cheek Plates
Upper Cheek Plate
Protect the upper chamber sidewalls. Check left/right side, thickness, hole spacing, edge profile and overlap with lower cheek plates.
View General Parts and Applicable Materials →
04
Lower Cheek Plates
Lower Cheek Plate
Located in the high-wear lower chamber. Confirm left/right side and wear allowance against the discharge opening, material flow and attachment method.
View General Parts and Applicable Materials →
05
Intermediate Plates and Protection Plates
Intermediate & Protection Plates
Intermediate plates adjust crushing chamber geometry; protection plates reduce wear behind the jaw plate on the frame. Check each separately for model, position, thickness, profile and fit with jaw retention parts.
View general intermediate plate guidance →06
Feed Guides and Inlet Protection
Deflector & Feed Protection
Protect the feed zone and material-facing frame surfaces against large-lump impact and uneven flow. Confirm the assembly drawing, left/right orientation, thickness and hole pattern.
View general feed guide guidance →Spare Parts
Pitmans, Eccentric Shafts, Bearings and Adjustment Systems
Check shaft diameters, fits, accuracy, heat treatment, lubrication, installed configuration and drawing revision separately for drivetrain and load-bearing parts.
01
Eccentric Shafts
Eccentric Shaft
Drive the pitman's reciprocating movement. Check eccentricity, journals, tapers, keyways, oil holes, bearing fits and heat-treatment requirements.
View general eccentric shaft guidance →
02
Spherical Roller Bearings and Housings
Spherical Roller Bearings & Housings
Support the eccentric shaft and pitman. Check bearing designation, clearance, housing bores, journals, lubrication system and labyrinth seals.
View general bearing guidance →
03
Toggle Plates and Toggle Seats
Toggle Plate & Seats
Transmit crushing loads and contribute to overload protection. Check length, thickness, curved end surfaces, seat fit and discharge-opening adjustment range.
View general toggle plate guidance →
04
Discharge-Setting Wedges
CSS Adjustment Wedges
For mechanical or hydraulic setting adjustment. Check left/right parts, wedge angle, guiding surfaces, hydraulic interfaces and ASC configuration.
View general adjustment wedge guidance →
05
Tension Rods and Tension Springs
Tension Rod & Spring
Maintain the toggle system's working position. Check rod diameter, thread, free length, spring rate, preload and connections.
View general tension rod guidance →
06
Labyrinth Seals and Lubrication Parts
Labyrinth Seals & Lubrication Parts
Exclude dust from bearings and retain lubricant. Check ring diameters, clearances, mating parts, oil passages and lubrication method.
View general labyrinth seal guidance →FAQ
Frequently asked questions
What information is needed for a C Series jaw plate quotation?
Provide the full model, serial number, tooth profile, movable or fixed side, jaw plate number, used-part photographs, key dimensions and operating conditions.
Does knowing C120 or C130 identify the jaw plate number?
No. A model can use different tooth profiles and movable/fixed jaw combinations. Check the plate number, drawing and installed configuration.
Where can I find confirmed jaw plate references and lifting tools?
Open the C Series page to find jaw plate references by model and tooth profile, and lifting tool numbers and rated capacities by applicable model.
More Component Pages
Browse component descriptions, drawing requirements and enquiry details.
- Discharge-Setting Wedges
- Feed Guide Plates
- Eccentric Shafts
- Fixed Jaw Plates
- Intermediate Plates
- Jaw Crusher Jaw Dies and Protection System
- Jaw-Plate Clamping Wedges
- Lower Cheek Plates
- Movable Jaw Plate
- Pitman and front casting protection plates
- Spherical Roller Bearings
- Tension Rods
- Toggle Plates
- Toggle Seats
- Upper Cheek Plates