Identify the mobile unit first, then its installed jaw crusher, cone crusher, HSI, VSI or screen box to find the relevant wear parts, spares, materials and enquiry route.
Mobile equipment is not a single crusher family. This page lists current mobile models, then directs parts enquiries to shared technical pages according to the installed jaw crusher, cone crusher, HSI, VSI or screen box.
Models follow Sandvik's current mobile product navigation. The installed machine or configuration may change between production years within a series, so parts cannot be identified from the mobile unit's appearance alone.
| Equipment category | Current models | Part identification route |
|---|---|---|
| Mobile jaw crushers | QJ241, QJ341, QJ341+; UJ210, UJ300, UJ310, UJ313, UJ440i, UJ443E, UJ516E, UJ640E | First confirm the installed jaw crusher model and chamber |
| Mobile cone crushers | QS332; QH332, QH441, QH443E; US316, US373, US440i, US440E, US640E; UH311, UH312, UH316, UH320E, UH373, UH412, UH440i, UH440E, UH640E; UK373; UD211 | First confirm the installed cone crusher model, chamber and screening module |
| Mobile HSI impact crushers | QI341, QI353, QI442; UI310, UI310+ | First confirm the installed HSI model, rotor and impact-apron configuration |
| Mobile VSI equipment | UV210, UV312, UV320E | First confirm the installed VSI model, rotor size and drive |
| Mobile screens | QA335, QA442, QA442e, QA452, QA452e; UF320E, UF373, UF473 | Check screen-box model, deck count, screen dimensions and aperture |
| Mobile scalpers | QE141, QE241, QE342, QE342e, QE442, QE442e, QE442 Free Flow, QE442e Free Flow | Check grizzly or screen box, feed area, screening media and conveyor configuration |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Main conveyor belt | Discharge conveyor on the left | QJ341 unit photo in technical-specification brochure |
| 2 | Track assembly | Undercarriage beneath the main unit | QJ341 unit photo in technical-specification brochure |
| 3 | Feed hopper | Elevated rear inlet | QJ341 unit photo in technical-specification brochure |
The mobile unit identifies the installation; wear parts are ultimately specified through the shared component page for its jaw crusher, cone crusher, HSI, VSI or screen box.
Mobile Jaw Crusher Jaw Dies
For the installed crushing chamber in QJ/UJ mobile jaw units. Check the mobile model, then the jaw crusher model, fixed or moving side, tooth profile, chamber and drawing.
View the common part page →
Mobile Cone Crusher Mantle
For installed cone chambers in QH/UH/US/QS and other mobile units. Check the mobile unit, installed cone model, chamber, mantle drawing and liner combination.
View the common part page →
Mobile Cone Crusher Concave
Forms the mobile cone crusher chamber with the mantle. Check upper, middle and lower sections, chamber, orientation, drawing and the matched mantle set.
View the common part page →
Mobile HSI Blow Bar
For QI/UI mobile impact crushers. Check mobile unit, installed HSI model, rotor slot, blow-bar section, length, weight, locking structure and orientation.
View the common part page →
Mobile VSI Rotor Wear System
For UV mobile VSI units. Check mobile model, installed VSI model, rotor size, ports, material discharge system, installation position and orientation.
View the common part page →
Mobile Screening Media
For QA/UF/QE mobile screens and scalpers. Check mobile unit, screen-box model, deck count, aperture, module size, fastening and flow direction.
View the common part page →Other spares also require dual identification of the mobile unit and installed equipment, with checks for orientation, interfaces, fits, lubrication and revision.
Jaw Crusher Eccentric Shaft & Bearings
Identify the installed jaw crusher first, then check shaft diameter, eccentricity, bearing seats, keyways, rotation, bearing designation, clearance and lubrication.
View the common part page →
Cone Crusher Countershaft Bushing
Supports the installed cone crusher countershaft. Check mobile unit, installed crusher, position, bore and outside diameter, length, oil grooves, fit and lubrication.
View the common part page →
HSI Rotor & Shaft System
For the HSI installed in QI/UI units. Check rotor diameter and width, blow-bar slots, shaft ends, rotation, inertia, bearings and dynamic-balancing requirements.
View the common part page →
VSI Main Shaft & Bearings
For the VSI installed in UV units. Check mainshaft, rotor interface, full bearing designation, speed, clearance, seals, lubrication, runout and dynamic balance.
View the common part page →
Screen Support Springs
Support and isolate QA/UF/QE screen boxes. Check box model, position, outside and wire diameters, free height, stiffness, quantity and matched set height.
View the common part page →
Screen Modular Panel Frame
Support modular panels in mobile screens. Check screen-box model, deck count, module dimensions, grid layout, fastening interfaces and installation datums.
View the common part page →Usually not. Confirm the full suffix, serial number, production year, installed crusher or screen-box nameplate and configuration revision.
No duplicate pages are created. Once the mobile installation is identified, use the shared component page for the relevant jaw crusher, cone crusher, HSI, VSI or screen box.
Yes. Submit both mobile-unit and installed-equipment nameplates, part position, used-part photos, key dimensions or drawings so we can identify the part first.
Provide the full mobile model and serial number, installed crusher or screen-box nameplate, part position, numbers, photos, drawings, material and operating conditions for identification and supply.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry