Identify the mobile unit first, then its installed jaw crusher, cone crusher, HSI, VSI or screen box to find the relevant wear parts, spares, materials and enquiry route.
Mobile equipment is not a single crusher family. This page lists current mobile models, then directs parts enquiries to shared technical pages according to the installed jaw crusher, cone crusher, HSI, VSI or screen box.
Models follow Sandvik's current mobile product navigation. The installed machine or configuration may change between production years within a series, so parts cannot be identified from the mobile unit's appearance alone.
| المعدات category | Current models | Part identification route |
|---|---|---|
| Mobile jaw crushers | QJ241, QJ341, QJ341+；UJ210, UJ300, UJ310, UJ313, UJ440i, UJ443E, UJ516E, UJ640E | First confirm the installed jaw crusher model and chamber |
| Mobile cone crushers | QS332；QH332, QH441, QH443E；US316, US373, US440i, US440E, US640E；UH311, UH312, UH316, UH320E, UH373, UH412, UH440i, UH440E, UH640E；UK373；UD211 | First confirm the installed cone crusher model, chamber and screening module |
| Mobile HSI impact crushers | QI341, QI353, QI442；UI310, UI310+ | First confirm the installed HSI model, rotor and impact-apron configuration |
| Mobile VSI equipment | UV210, UV312, UV320E | First confirm the installed VSI model, rotor size and drive |
| Mobile screens | QA335, QA442, QA442e, QA452, QA452e；UF320E, UF373, UF473 | Check screen-box model, deck count, screen dimensions and aperture |
| Mobile scalpers | QE141, QE241, QE342, QE342e, QE442, QE442e, QE442 Free Flow, QE442e Free Flow | Check grizzly or screen box, feed area, screening media and conveyor configuration |
Before manufacture or quotation, confirm the full mobile-unit model, serial number, installed crusher or screen-box nameplate, part position, drawing number, drawing and configuration revision.
The mobile unit identifies the installation; wear parts are ultimately specified through the shared component page for its jaw crusher, cone crusher, HSI, VSI or screen box.
Mobile Jaw Crusher Jaw Dies
For the installed crushing chamber in QJ/UJ mobile jaw units. Check the mobile model, then the jaw crusher model, fixed or moving side, tooth profile, chamber and drawing number.
Material selection: Confirm manganese steel or a service-validated composite wear system against impact, abrasion, feed grading and target life.
View the common part page →
Mobile Cone Crusher بطانة المخروط المتحرك
For installed cone chambers in QH/UH/US/QS and other mobile units. Check the mobile unit, installed cone model, chamber, mantle drawing number and liner combination.
Material selection: Confirm manganese steel or a specific composite wear solution against chamber type, ore abrasiveness, feed grading and reduction ratio.
View the common part page →
Mobile Cone Crusher Concave
Forms the mobile cone crusher chamber with the mantle. Check upper, middle and lower sections, chamber, orientation, drawing number and the matched mantle set.
Material selection: Confirm manganese steel or a validated composite wear system against impact hardening, abrasive wear and chamber matching.
View the common part page →
Mobile HSI قضيب صدم للكسارة الصدمية
For QI/UI mobile impact crushers. Check mobile unit, installed HSI model, rotor slot, blow-bar section, length, weight, locking structure and orientation.
Material selection: Confirm high-chromium iron, chromium-molybdenum alloy steel, martensitic steel or a composite solution against impact, abrasion and tramp-metal exposure.
View the common part page →
Mobile VSI Rotor Wear System
For UV mobile VSI units. Check mobile model, installed VSI model, rotor size, ports, material discharge system, installation position and orientation.
Material selection: Confirm carbide, high-chromium wear materials or composites against high-speed abrasion, impact, fracture and dynamic-balancing requirements.
View the common part page →
Mobile Screening Media
For QA/UF/QE mobile screens and scalpers. Check mobile unit, screen-box model, deck count, aperture, module size, fastening and flow direction.
Material selection: Confirm polyurethane, rubber or wire mesh against abrasion, impact, wet screening, dewatering, open area and target size fraction.
View the common part page →Other spares also require dual identification of the mobile unit and installed equipment, with checks for orientation, interfaces, fits, lubrication and revision.
Jaw Crusher Eccentric Shaft & Bearings
Identify the installed jaw crusher first, then check shaft diameter, eccentricity, bearing seats, keyways, rotation, bearing designation, clearance and lubrication.
Material selection: Confirm forged transmission alloy steel and bearing steel against loads, fatigue, heat treatment, accuracy and nondestructive examination requirements.
View the common part page →
Cone Crusher Countershaft Bushing
Supports the installed cone crusher countershaft. Check mobile unit, installed crusher, position, bore and outside diameter, length, oil grooves, fit and lubrication.
Material selection: Confirm bearing copper alloy or the original-design plain-bearing material against contact pressure, sliding speed, lubrication, temperature rise and clearance.
View the common part page →
HSI Rotor & Shaft System
For the HSI installed in QI/UI units. Check rotor diameter and width, blow-bar slots, shaft ends, rotation, inertia, bearings and dynamic-balancing requirements.
Material selection: Confirm rotor structure, forged shaft, bearings and locking parts separately against strength, fatigue, impact, heat treatment and dynamic balance.
View the common part page →
VSI العمود الرئيسي & Bearings
For the VSI installed in UV units. Check mainshaft, rotor interface, full bearing designation, speed, clearance, seals, lubrication, runout and dynamic balance.
Material selection: Confirm forged transmission alloy steel and bearing steel against high-speed loads, heat treatment, accuracy, temperature rise and flaw-detection requirements.
View the common part page →
Screen Support Springs
Support and isolate QA/UF/QE screen boxes. Check box model, position, outside and wire diameters, free height, stiffness, quantity and matched set height.
Material selection: Confirm spring steel or elastomer buffers against load, amplitude, frequency, fatigue, temperature and set matching.
View the common part page →
Screen Modular Panel Frame
Support modular panels in mobile screens. Check screen-box model, deck count, module dimensions, grid layout, fastening interfaces and installation datums.
Material selection: Confirm structural steel, wear-resistant covering and elastic inserts against vibration fatigue, corrosion, wear and screen-panel fastening.
View the common part page →Available traceable records do not yet provide a public parts list covering every mobile model and installed-equipment revision. This page does not publish inferred numbers.
Application rule: The mobile-unit number cannot replace the installed-equipment number. Before manufacture, check both nameplates, configuration revisions, position, drawing number or drawing, key dimensions and material.
Usually not. Confirm the full suffix, serial number, production year, installed crusher or screen-box nameplate and configuration revision.
No duplicate pages are created. Once the mobile installation is identified, use the shared component page for the relevant jaw crusher, cone crusher, HSI, VSI or screen box.
Yes. Submit both mobile-unit and installed-equipment nameplates, part position, used-part photos, key dimensions or drawings so we can identify the part first.
Provide the full mobile model and serial number, installed crusher or screen-box nameplate, part position, numbers, photos, drawings, material and operating conditions for identification and supply.
رقم الهاتف: +86 156 3797 3199
zzx@anranst.com
توفر شركة ANRANST للعملاء العالميين تقييمات هندسية، واختيار التصنيع الصيني، ومراقبة الجودة، وتسليم الأجزاء النهائية لقطع الغيار الصناعية المقاومة للتآكل حسب الطلب، ويمكنها أيضًا دعم قطع الغيار الصناعية الأخرى حسب الطلب.
قم بمراجعة أسطح التزاوج وأبعاد الواجهة، وقم بتقييم جدوى المواد والمعالجة الحرارية والتصنيع.
تُحدَّد درجات المواد وعمليات المعالجة الحرارية لكل طلب على حدة، وتُثبَّت في الاتفاقية الفنية وتُتابَع أثناء الإنتاج.
يشمل ذلك تأكيد الرسم، ومراقبة المواد والعمليات، وتتبع الإنتاج، وتنسيق عمليات الفحص والقبول.
تنظيم عمليات التصنيع والتحقق من الجودة والتعبئة والتغليف وتسليم المنتجات النهائية الكاملة لتشكيل حلقة إمداد قابلة للتنفيذ.
قم بتزويدنا بالنماذج الحالية، والرسومات، وأرقام الرسومات، وأرقام الأجزاء، والمواد، أو معلومات ظروف التشغيل، وسنقوم بتحديد التحقق الفني ومسار التوريد وفقًا لذلك.
إرسال طلب