Start with the current SK, SM and S ranges to find screen panels, mesh, liners, deck frames, support springs, tensioning parts, materials and quotation options.
The current public range is organized into SK, SM and S and their screen types. This page does not invent standard dimensions: screen type, screening surface, deck count, drive and part position form the basis for technical checks.
Sandvik publishes screen types rather than a single standard-size model system. This table retains official ranges and public screen types; check length, width, deck count, aperture, drive and exciter against installed-equipment documents.
| Product range | Screen type | Key identification details | Dimension basis |
|---|---|---|---|
| SK Range | SL Flat deck | Flat-deck screen; confirm wet/dry duty, deck count and screening configuration | Customized |
| SK Range | SM Multislope | Multislope screen for high-throughput classification | Customized |
| SK Range | SA Flat deck | Flat-deck screen; confirm screening surface and drive configuration | Customized |
| SK Range | SG Grizzly | Heavy-duty grizzly for prescreening and fines removal | Customized |
| SK Range | SN Multislope | Single- or double-deck multislope screen with vibrating motors | Customized |
| SK Range | SV Dewatering | Dewatering screen; confirm screening surface, open area and drainage requirements | Customized |
| SM Range | SM Multislope | Single- or double-deck multislope screen with DF exciters | Customized |
| SM Range | SL Linear flat | Single- or double-deck linear flat screen with DF exciters | Customized |
| SM Range | SG Linear grizzly | Heavy-duty linear grizzly for prescreening crusher feed | Customized |
| SM Range | SA Flat | Single- or double-deck linear flat screen with vibrating motors | Customized |
| S Range | SA Inclined | Inclined screen | Customized |
| S Range | SJ Inclined | Inclined screen | Customized |
| S Range | SL Horizontal | Horizontal screen | Customized |
| S Range | SS / SF Free-fall | Free-fall screen | Customized |
| S Range | SR Roller | Roller screen | Customized |
| S Range | SG Grizzly | Grizzly screen | Customized |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Screening media | Visible stepped screening surface at the top | SF OEM family view (dimensions not specified) |
| 2 | Support springs | Spring support beneath the screen box | SF OEM family view (dimensions not specified) |
| 3 | Vibration motors | Drive module beneath the screen box | SF OEM family view (dimensions not specified) |
| 4 | Side plates | Structural plates along the screen-box sides | SF OEM family view (dimensions not specified) |
Check panels and mesh by aperture, module size, fastening, flow direction and screening duty. Identify liners separately in feed, sidewall, discharge and bearing areas.
Polyurethane Screen Panel
Installed on the deck for classification or dewatering through the apertures. Check aperture shape and size, panel thickness, module dimensions, fastening, flow direction, open area and screening duty.
View the common part page →
Screen Mesh / Wire Mesh
For dry or wet classification. Check aperture, wire diameter, weave, width, length, tension direction, edge form and deck count.
View the common part page →
Feed Box Liner
Protect the feed area and cushion concentrated material flow. Check position, plate sequence, holes, thickness, overlaps and feed direction.
View the common part page →
Side Plate Liner
Protect screen-box sidewalls in contact with the material bed. Check left/right side, front/rear position, plate numbers, holes, thickness and overlap with the deck.
View the common part page →
Discharge Chute Liner
Protect oversize or undersize discharge chutes. Check the outlet served, flow direction, plate sequence, holes, thickness and overlaps.
View the common part page →
Bearing Housing Protection Liner
Protect exposed structures near bearing housings from falling and flowing material. Check housing position, plate profile, holes, thickness and maintenance clearance.
View the common part page →
Capping Rubber
Fitted between mesh and support or clamping points to cushion vibration and protect mesh edges. Check section, length, groove width, orientation and matching rails.
View the common part page →Confirm structural and support parts by screen type, deck count, deck dimensions, amplitude, frequency, load, orientation and installation datums.
Deck Frame
Carry the screening surface and material bed. Check screen type, deck count, length, width, cross-member layout, connecting holes, crown height, tensioning method and installation datums.
View the common part page →
Modular Panel Frame
Support modular panels while maintaining module spacing and deck flatness. Check module dimensions, grid layout, fastening interfaces, deck count and structural datums.
View the common part page →
Support Spring / Buffer
Support the screen box and isolate dynamic loads. Check outside and wire diameters, free height, stiffness, quantity, position and matched set height.
View the common part page →
Tension Rail / Wedge
Secure tensioned mesh and maintain deck preload. Check screening direction, rail section, wedge angle, length, holes and left/right arrangement.
View the common part page →No. The same type designation can occur in different ranges. Provide the SK/SM/S range, complete nameplate, deck dimensions and count, and equipment documents.
No. Also check module dimensions, thickness, aperture shape, fastening, flow direction, deck layout, material and wet or dry screening conditions.
Yes. Submit the nameplate, installation position, used-part photos, key dimensions or drawings so we can identify the part first.
Provide the complete nameplate, SK/SM/S range, screen type, deck dimensions and count, part position, drawings or samples, photos, drawings, material and conditions for identification and supply.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry