Start with the brand, equipment series and installed machine, then explore wear parts, drive and structural spares, materials and processes, drawing review, quality control and finished-part delivery.
This page covers equipment series and models, part locations, materials and processes, drawing review and inquiry options. Before manufacture or quotation, confirm OEM drawing numbers, dimensions and tooling suitability against the complete model and drawings.
The model table assists with machine identification. Manufacture and quotation require the nameplate, complete model, serial number, drawing number, general arrangement and drawing revision.
| Series / Model | Equipment Range and Identification | Equipment History and Identification |
|---|---|---|
| POLYCOM | High-pressure grinding roll (HPGR) range for minerals and cement raw materials; verify roll diameter, roll width and drive configuration against the specific model and drawing. | Polysius Product Range |
| QUADROPOL | Vertical roller mill range for cement raw material and slag grinding | Polysius Product Range |
| POLYTRACK | Clinker cooler range using a stationary aeration floor with a material transport system above it | Polysius Product Range |
| DOROL | Two-roller vertical mill range, including earlier models | Polysius legacy product range |
| ROTARY KILN | Rotary kiln range for cement clinker production | Polysius Product Range |
| BALL MILL | Tube mill and ball mill range for cement and mineral grinding | Polysius Product Range |
These general High Pressure Grinding Rolls part categories help identify the part you need. Confirm suitability against the specific thyssenkrupp Polysius model and drawings.
Edge Protection / Edge Liner
A general wear part category for High Pressure Grinding Rolls equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Cheek Plate / Side Liner
A general wear part category for High Pressure Grinding Rolls equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Feed Chute Liner
A general wear part category for High Pressure Grinding Rolls equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Discharge Chute Liner
A general wear part category for High Pressure Grinding Rolls equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Scraper / Cleaner
A general wear part category for High Pressure Grinding Rolls equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Press Frame Liner
A general wear part category for High Pressure Grinding Rolls equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →Identify gears, shafts, sleeves, bearings, seals, hydraulic parts, supports and connectors for drawing review. Listed OEM drawing or part references relate to identified parts and require confirmation against your machine.
Bearing / Bearing Seal
A general structural or drive part category for High Pressure Grinding Rolls equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Hydraulic Cylinder Seal
A general structural or drive part category for High Pressure Grinding Rolls equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →Provide the complete model, serial number, drawing or part number, drawing revision, installation position, photographs of the current part, material and operating conditions.
No. General images help identify the part category. Manufacture requires agreed drawings, dimensions, interfaces, materials and acceptance criteria.
Start with the nameplate, general arrangement drawing, installation position, used-part photographs and key dimensions. We can then assess the feasibility of dimensional inspection, material evaluation and manufacture to drawing.
Provide the complete model, serial number, nameplate, installation position, photographs of the current part, drawings, material and operating conditions. We use these to identify the part, assess materials, match manufacturing resources, coordinate quality control and arrange finished-part delivery.
Phone: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with coordinated consulting, supplier sourcing, quality control and finished-part delivery for custom parts, wear parts and industrial spares from China, with scope to support other custom industrial parts.
Equipment and part identification, drawing review, material selection and manufacturing feasibility assessment.
Match requirements with suitable manufacturers in China and coordinate the exchange of technical information.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
Coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts.
Provide the existing model, drawings, drawing or part numbers, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry