Weir Cavex Hydrocyclones

Cavex 2 hydrocyclone Original factory open-plan; used Identification The feed head, Housing Sub-paragraphs, Shell, Cone and Underflow Outlet.

Cavex 2 The original factory explosion diagram; display feed head, eddy stream conductor tubes. Shell, Cone slab and spigot The order of assembly.

Cavex rubber The lining of the original factory physical figure; a frame, an outline and cardboard Interfaces And the thickness must be specific Series Confirmation with nominal diameter.

OEM Equipment Details

Series, Dimensions and Connectivity Interfaces The same page closed loops

This page is used to identify Cavex hydrocyclonewear parts with spare parts. The mainframes are determined by the complete series, nominal diameter and shell/liner structure as well AS interface on site; then manufacturing confirmation will be completed in nameplate: general arrangement drawing (the original outline), flange pores system(S) or actual internal radius of operation conditions).

7 Current Equipment Series

40–1,450 mm Open nominal diameter range

≤250 kPa Series Public Pressure Lobby

12 wear parts and spare parts Category

Standard Models and Key Dimensions

Cavex Standard Series and Key dimensions

Series, nominal diameters Housing, Lifts and pressure & temperature press Weir Current Cavex Official product page.

Standard Series	Template: Nominal diameter range	Housing With the spool Construction	Open pressure / Temperature range
Cavex 2	40–800 mm	Metals or DMC Housing; R55/Linatex rubber Or as a whole ceramic sling	0–250 kPa; 0–80°C
Cavex CVX	40–1,200 mm	Corrosion resistance materials, polyester or Carbon Steel Housing; rubber, ceramic or polyurethane sling	0–250 kPa; 0–80°C
Cavex CVXA	400–650 mm	Overall High-Chromium White Cast Iron Construction, without independent sewers	0–250 kPa; 0–80°C
Cavex CVXT	250–1,450 mm	Steel-based steel Housing; ceramic Brick slat	0–250 kPa; 0–80°C
Cavex CVXU	40–250 mm	Overall polyurethane Construction.Without independence Housing	0–175 kPa; 0–70°C
Cavex DE	250–650 mm	Metallurgical Housing; rubber, Overall ceramic or polyurethane sling	0–250 kPa; 0–80°C
Cavex Dewatering	150–800 mm	Metals or DMC Housing; rubber or ceramic sling	≤100 kPa; 0–80°C

The whole series, nominal diameters and feed vortex flowing tube are still required to be matched with a range of cone anglers (cones), feeding chamber or inverter stream conductors. Spare parts manufacturing must also verify the complete seriality; name Diameter: input rotational direction - type forging linen lines -- flangion hole systems — current items as well AS operating conditions on site

Wear Parts

Injection cavity, cone linings and overflowing flow wear parts

The wear parts are arranged by the actual flow of mineral slurry through location.The material pages for initial screening, and final materials in terms such as their range or original structure; abrasion shapes:

Injection head and feed lining

Inlet Head & Feed Chamber Liner

The feed cavity is the first position to confirm vortex, entrance section and wire interface. Orders require a series of check-ups with nominal diameter; direction for supplies: shell hole system (SPI) or current profile in liners

Material Selection: by Series Modular pressures can be used rubber, Overall ceramic or polyurethane Specifics; materials With thickness must be abrasive, granularity and pressure according to the mineral pulp. Construction Confirmation.

Rubber and Polyurethane Wear ceramics

View Part Details →

Shell Off the upper side

Cylinder & Upper Liner

The cylinder upper frame carries the incoming cavity spindle and protects its shell. Different series of segments, slot machines or flanges are different from their thickness to not only be exchanged by external diameter

Material Selection: rubber suitable for absorption of shock and resistance to mineral sludge abrasion; ceramic Applicable for high abrasion stability operating conditions; polyurethane Applicable for small diameter and fine grading Series.

Rubber and Polyurethane Wear ceramics

View Part Details →

Cone With the lower spool

Cone & Lower Liner

Cone lining controls the flow field by stage contraction and withstands continuous sliding wear. The cones are required to check each segment of a narrow angle, length; upper-bottom calibre: flanged hole system (SQ), number incremental quantity or order for installation.

Material Selection: materials Abrasion, shocks and temperature risks are jointly determined; rubber, ceramic and polyurethane Not to be separated from specific Series and Construction Generally replace.

Rubber and Polyurethane Wear ceramics

View Part Details →

Pipes with eddy stream conductors

Overflow Pipe & Vortex Finder

The eddy stream conductor determines the effective diameter and depth of a spillway, directly affecting grade cutting with short circuit flows. Nuclear outer radius is required for internal distance; length: flange as well AS fixed structure

Material Selection: Common paths are Wear-resistant rubber, polyurethane or ceramic Construction, and finally by Series, Size and site wear location confirmation.

Rubber and Polyurethane Wear ceramics

View Part Details →

spigot, Underflow Outlet Offlinings with the inner

Apex, Spigot & Insert

Spigot is one of Cavex's official high wear positions. Internal radial changes affect the bottom line shape and grade performance, with orders to check series appearance as well in connection mode or actual internal diameter balance for abrasion.

Material Selection: Can be pressed Series Utilization rubber, polyurethane or ceramic Abrasion Construction; can not be determined only by the color, appearance or aperture after wear of old items model.

Rubber and Polyurethane Wear ceramics

View Part Details →

Entrance short tube and overflow pipe strap

Inlet Nozzle & Overflow Pipe Liner

The entrance short tube, overflow pipe and connection lining withstand local high speed brushing to connect the field pipeline. It is necessary for a check of interface direction; flange standard (orifica), boreal system: internal diameters - length & seal surface

Material Selection: Frames by pulp, pressure and temperature Interfaces Choices rubber, polyurethane or ceramic; Seals By the medium and Refining Grooves Confirmation.

Rubber and Polyurethane Seals and Engineering Plastics

View Part Details →

Spare Parts

Housing, Interfaces, Specifications and Torpedo Group spare parts

Cavex is a non-rotating part, with Spare parts focusing on shell segments and feed headers; specifications inserts are attached to the connector parts for sealing or thumbnail groups. No transmission/maintenance areas that do not relate directly either of this equipment shall be set up in any way whatsoever

Housing, Shell and Cone Sub-paragraph

Housing, Cylinder & Cone Sections

Fixing and keeping the straps Geometry Streaming: Metals or DMC Housing, Cone angles and length of segments; Flanged outer diameter. Mounting Orders.

Material Selection: Housing materials and anti-corruption system Series and the media is determined; CVXA Overall High-Chromium White Cast Iron Construction Fixing metal should not be used Housing Logical.

High-Chromium White Cast Iron Composite and Engineering materials

View Part Details →

Injection head, entrance connection and duct

Feed Chamber, Inlet & Nozzle

The feed head determines the cut-in and twitch. spare parts Recognizes the need to provide both entry direction, internal diameter of a port yard and flange contours. Pressure rating as well are also available on site traffic photos

Material Selection: Pressure Housing, wear-resistant straps and Seals It should be confirmed separately, not in a single Material Information Whole whole cum.

Abrasion liner materials Seals and Engineering Materials

View Part Details →

Wind-current conductor tubes and specifications insertion

Vortex Finder & Size Insert

For the matching of effective overflows for different tiered requirements. The dimensions must be verified at once by insertion depth, external fixation and existing internal diameter Wear condition.

Material Selection: by Series Can be used rubber, polyurethane, ceramic or composite Construction; Dimensions and Geometry Relationships prioritize materials Alternatives.

Rubber and Polyurethane Wear ceramics

View Part Details →

spigot Suites with Specification

Spigot & Apex Size Kit

Used for recovery or adjustment Underflow Outlet Sizes. The body, lining or insertion form must be confirmed and the dimensions are of one size Mounting Interfaces.

Material Selection: Wear-Resistant Materials Need to balance service life and aperture stability; specific materials and size by Cavex Series and operating conditions Confirmation.

Rubber and Polyurethane Wear ceramics

View Part Details →

Quickly disassembled, flange and fasteners

Quick-release Clamps, Flanges & Fasteners

Part of the size Configuration Quickly disconnected. procurement The shape of the clipping, flange outer diameters and pores shall be checked against; Quantity, Seals and pressure requirements.

Material Selection: fasteners and fixtures according to the pressure, corrosion protection requirements; Seals By medium, temperature and flange Refining Grooves Choices.

Highly strong connectors alloy steel Seal Materials

View Part Details →

Complete cyclonics and Mounting Interfaces

Complete Cyclone & Mounting Interface

The field can be configured to reserve the full cyclone unit on install. Even if nominal diameter is identical, feed rotations and flanges with bracketing or a collector'd valve as well for inspection space may still vary

Material Selection: The complete singles should be separately confirmed by the pressure Housing, wear-resistant straps and sealing parts materials Corruption Prevention and Anti-Crime Acceptance Demand.

sludge pipe wearable strap Continuing and corrosion-resistant Structural material

View Part Details →

Only know Cavex Can the diameter be directly determined lining and spigot ？

Cannot. The complete series, feed vortexes and cone angles are also required to confirm the shell & wire version of a coiled stream pipe with an inverter tube for Spigot internal diameter; flangal bore systems as well on-site operating conditions can be configured differently at same size

Cavex Can the slate be rubber, ceramic and polyurethane Replacement between?

Can't just press materials Name replacement. The lining outline, thicknesses and card slots or bonding methods must be verified at the same time Housing Couple, mineral smear resistance and particle size.

Why this page is not unconfirmed Cavex OEM Part Number ？

No numbers supported by traceable original catalogs, drawings or installments are published in public. Nameplate lets may be submitted to the name plate series and nominal diameter of used parts photos with dimensions as well for any known drawing number that is not available on a date basis

Weir Cavex Hydrocyclones

Series, Dimensions and Connectivity Interfaces The same page closed loops

Cavex Standard Series and Key dimensions

Injection cavity, cone linings and overflowing flow wear parts

Injection head and feed lining

Shell Off the upper side

Cone With the lower spool

Pipes with eddy stream conductors

spigot, Underflow Outlet Offlinings with the inner

Entrance short tube and overflow pipe strap

Housing, Interfaces, Specifications and Torpedo Group spare parts

Housing, Shell and Cone Sub-paragraph

Injection head, entrance connection and duct

Wind-current conductor tubes and specifications insertion

spigot Suites with Specification

Quickly disassembled, flange and fasteners

Complete cyclonics and Mounting Interfaces

Only know Cavex Can the diameter be directly determined lining and spigot ？

Cavex Can the slate be rubber, ceramic and polyurethane Replacement between?

Why this page is not unconfirmed Cavex OEM Part Number ？

Submission Cavex Series, diameters and the strapping drawing number or old information

From Technical Assessment to Finished-Part Delivery

Technical Advice

Supplier Introductions

Quality Control

Finished-Part Delivery