ELITE double-deck banana screens, Orbital C inclined circular-motion screens, Orbital E horizontal elliptical-motion screens and VD dewatering screens. Use model and deck dimensions to identify media, liners, exciters, bearings, springs and drive spares.
First identify the machine by ELITE, Orbital C/E or VD series and standard dimensions. Then select wear parts and spares by feed, deck, discharge, box, excitation and support positions. Manufacture requires the nameplate, full model, deck layout, general arrangement, used parts, duty and verified drawing.
Orbital C/E and VD data come from current official Weir specifications. ELITE is an engineered series; the table gives its officially published maximum deck size and operating range.
| Standard Model / Configuration | Deck Dimensions and Count | Screening Area / Duty Limit | Excitation, Power and Mass |
|---|---|---|---|
| ENDURON ELITE banana screen (engineered) | Double deck; maximum published deck 4.27 × 8.53 m | 4.5–5 G; high-throughput fine screening | 2 ETX exciters; up to approximately 50 t |
| Orbital C15483S | 1,535 × 4,880 mm; 3 decks | 22.5 m²; maximum feed 150 mm | ECX025S; 15 kW; sprung mass 5.9 t |
| Orbital C15484S | 1,535 × 4,880 mm; 4 decks | 30.0 m²; maximum feed 150 mm | ECX025S; 18.5 kW; sprung mass 7.6 t |
| Orbital C18482S | 1,840 × 4,880 mm; 2 decks | 18.0 m²; maximum feed 150 mm | ECX025S; 15 kW; sprung mass 5.0 t |
| Orbital C18483S | 1,840 × 4,880 mm; 3 decks | 26.9 m²; maximum feed 150 mm | ECX025S; 18.5 kW; sprung mass 6.8 t |
| Orbital C18612S | 1,840 × 6,100 mm; 2 decks | 22.4 m²; maximum feed 150 mm | ECX025S; 15 kW; sprung mass 5.8 t |
| Orbital C18613S | 1,840 × 6,100 mm; 3 decks | 33.7 m²; maximum feed 150 mm | ECX035S; 18.5 kW; sprung mass 8.2 t |
| Orbital C18614S | 1,840 × 6,100 mm; 4 decks | 44.9 m²; maximum feed 150 mm | ECX035S; 22 kW; sprung mass 10.7 t |
| Orbital C18614L | 1,840 × 6,100 mm; 4 decks | 44.9 m²; maximum feed 150 mm | ECX035S; 22 kW; sprung mass 10.5 t |
| Orbital C24612S | 2,450 × 6,100 mm; 2 decks | 29.9 m²; maximum feed 150 mm | ECX045S; 18.5 kW; sprung mass 7.5 t |
| Orbital C24613S | 2,450 × 6,100 mm; 3 decks | 44.8 m²; maximum feed 150 mm | ECX045S; 22 kW; sprung mass 10.6 t |
| Orbital E18483S | 1,840 × 4,880 mm; 3 decks | 26.9 m²; maximum feed 150 mm | ECX050D; 22 kW; sprung mass 8.2 t |
| Orbital E18612S | 1,840 × 6,100 mm; 2 decks | 22.4 m²; maximum feed 150 mm | ECX070D; 22 kW; sprung mass 7.2 t |
| Orbital E18613S | 1,840 × 6,100 mm; 3 decks | 33.7 m²; maximum feed 150 mm | ECX070D; 37 kW; sprung mass 9.2 t |
| Orbital E24612S | 2,450 × 6,100 mm; 2 decks | 29.9 m²; maximum feed 150 mm | ECX090D; 37 kW; sprung mass 8.9 t |
| Orbital E24613S | 2,450 × 6,100 mm; 3 decks | 44.8 m²; maximum feed 150 mm | ECX090D; 45 kW; sprung mass 12.0 t |
| VD6 dewatering screen | 610 × 2,100 mm | Deck area 1.28 m²; installation angle 3–5° | Vibrating motor drive |
| VD9 dewatering screen | 915 × 2,440 mm | Deck area 2.23 m²; installation angle 3–5° | Vibrating motor drive |
| VD12 dewatering screen | 1,220 × 3,050 mm | Deck area 3.72 m²; installation angle 3–5° | Vibrating motor drive |
| VD12 dewatering screen | 1,220 × 3,660 mm | Deck area 4.47 m²; installation angle 3–5° | Vibrating motor drive |
| VD15 dewatering screen | 1,525 × 3,660 mm | Deck area 5.58 m²; installation angle 3–5° | Vibrating motor or exciter drive |
| VD15 dewatering screen | 1,525 × 3,810 mm | Deck area 5.81 m²; installation angle 3–5° | Vibrating motor or exciter drive |
| VD18 dewatering screen | 1,830 × 3,810 mm | Deck area 6.98 m²; installation angle 3–5° | Vibrating motor or exciter drive |
| VD21 dewatering screen | 2,135 × 4,880 mm | Deck area 10.42 m²; installation angle 3–5° | Exciter drive |
| VD24 dewatering screen | 2,440 × 4,880 mm | Deck area 11.91 m²; installation angle 3–5° | Exciter drive |
| VD24 dewatering screen | 2,440 × 6,100 mm | Deck area 14.88 m²; installation angle 5° | Exciter drive; published series capacity up to 250 t/h |
Media material and apertures jointly determine life and screening efficiency. Material pages support preliminary selection; confirm formulation, hardness, reinforcement, apertures, thickness and fastening against particle size, impact, abrasion, moisture and original design.
Polyurethane Modular Screen Panels
Modular panels take direct rock impact and sliding wear while controlling apertures and separation size. Current standard ENDURON modules are 305 × 305 mm, secured with pins and sleeves.
View the Component Page →
Rubber Modular Panels & Impact Panels
Rubber modules and feed impact plates absorb coarse-particle impacts, reduce noise and protect the box. Check module dimensions, apertures, fastening, thickness and backing reinforcement.
View the Component Page →
Side-tension Wire Mesh & Screen Deck
Orbital screens can use side-tensioned or modular media. For metal mesh, check wire diameter, apertures, woven or perforated design, tension direction, overlaps and edges.
View the Component Page →
Feed Box & Impact-zone Liners
The feed box and first deck section receive the greatest drop impacts and concentrated wear. Check feed direction, liner segmentation, holes, overlaps, cushioning and adjacent panels.
View the Component Page →
Side Plate, Crossbeam & Backplate Protection
Protection parts isolate sides, crossbeams and backs from material erosion and prevent box wear. Check each part's side, length, hole spacing, clamping and vibration clearance.
View the Component Page →
Discharge, Chute & Capping Protection
Discharge lips, chute liners, clamping rubber and edge seals protect the deck end and downstream interfaces. Check flow direction, drop height, apertures, clamping and connection dimensions.
View the Component Page →Screen spares require checks of dynamic loads, fatigue, balance and complete interfaces. Appearance or one dimension cannot establish interchangeability of exciters, bearings, springs, drives or screen boxes.
ELITE ETX Exciter Assemblies
Large ELITE double-deck banana screens use two ETX exciters. Supply screen dimensions, exciter nameplate, orientation, speed, eccentric-mass setting and drive interfaces to identify the assembly.
View the Component Page →
Orbital ECX Modular Exciter
C and E screens use removable modular exciters. Verify ECX025S, 035S, 045S, 050D, 070D or 090D and single/twin-shaft design against the C/E model.
View the Component Page →Exciter Shafts, Bearings, Gears & Seals
Current Weir literature states that C and E exciters share bearing, shaft and seal systems. Quotations still require the ECX model, serial number, part position and actual measurements.
View the Component Page →
Crossbeams, Backplates & Feedbox Structure
Orbital uses fully bolted modular construction; some crossbeams, back plates and feed boxes are interchangeable within the same model size. Manufacture requires general arrangements, hole patterns, plate thicknesses, preload and fatigue checks.
View the Component Page →
Support Springs, Buffers & Mounts
Springs and buffers determine isolation, working height and dynamic balance. Check free height, stiffness, load, left/right positions, rubber parts and mounts as matched groups.
View the Component Page →Motor, Coupling, Belt & Drive Base
The external drive transfers power to the exciter. Check motor power, speed, pulleys or coupling, rotation, guards, centre distance and base hole pattern.
View the Component Page →No. Verify material, hardness, aperture shape and size, thickness, backing reinforcement, pins and sleeves, deck slope section, level, feed size and moisture. Identical outer dimensions do not imply identical screening performance or interfaces.
Use the full C or E screen model to establish the ECX exciter, then check single/twin-shaft design, nameplate, serial number, bearings, shafts, seals, speed, orientation and eccentric settings.
Numbers without traceable OEM catalogues, drawings or installation records are not published. Verified references are assigned to part positions after obtaining the full model, deck layout, drawing, used part or reliable installation data.
Provide the full ELITE, Orbital C/E or VD model, nameplate, deck dimensions and count, apertures and media material, exciter model, drawing, used-part photographs and material conditions. These support identification, material assessment, manufacturing coordination, quality control and finished-part delivery.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the equipment brand, complete model and serial number, part name, part number or drawing number, drawing revision, quantity, material requirements and duty. If identifiers are unavailable, send photographs and key dimensions.
Submit an Enquiry