Rod mill · 1965 · 3 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Allis-Chalmers 12.5 × 15 ft Rod mill | 12.5 × 15′ Rod mill | 1965 | 7 |
| Allis-Chalmers 6 × 12 ft Rod mill | 6 × 12′ Rod mill | 7 | |
| Allis-Chalmers 9 × 12 ft Rod mill | 9 × 12′ Rod mill | 7 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Mill shell | Cylindrical mill shell | OEM overflow rod mill family; exact discharge/drive configurations of 6×12, 9×12, 12.5×15 units not specified |
| 2 | Shell liner | Inside lower mill shell | OEM overflow rod mill family; exact discharge/drive configurations of 6×12, 9×12, 12.5×15 units not specified |
| 3 | Mill heads | Discharge-end head | OEM overflow rod mill family; exact discharge/drive configurations of 6×12, 9×12, 12.5×15 units not specified |
| 4 | Mill trunnions | Outside discharge head | OEM overflow rod mill family; exact discharge/drive configurations of 6×12, 9×12, 12.5×15 units not specified |
| 5 | Main trunnion bearing | Discharge trunnion support | OEM overflow rod mill family; exact discharge/drive configurations of 6×12, 9×12, 12.5×15 units not specified |
| 6 | Girth gear | Outside discharge head | OEM overflow rod mill family; exact discharge/drive configurations of 6×12, 9×12, 12.5×15 units not specified |
| 7 | Drive pinion | Gear drive side in upper plan view | OEM overflow rod mill family; exact discharge/drive configurations of 6×12, 9×12, 12.5×15 units not specified |
Models with the same components are grouped together; select a group to open its component table.
Models: Allis-Chalmers 12.5 × 15 ft Rod mill, Allis-Chalmers 6 × 12 ft Rod mill, Allis-Chalmers 9 × 12 ft Rod mill
| No. | Component |
|---|---|
| 1 | Ball Mill Shells |
| 2 | Shell liner |
| 3 | Ball Mill Heads |
| 4 | Ball Mill Trunnions |
| 5 | Ball Mill Main Bearings, Bearing Shells and Housings |
| 6 | Girth Gear (Ring Gear) |
| 7 | Drive Pinion |
The Ball / Rod / Compeb Rod mill covers 3 models: Allis-Chalmers 12.5 × 15 ft Rod mill, Allis-Chalmers 6 × 12 ft Rod mill, Allis-Chalmers 9 × 12 ft Rod mill. Former and renamed designations are listed in the models table on this page.
The Ball / Rod / Compeb Rod mill is also documented under these designations: Allis-Chalmers 12.5 × 15 ft Rod mill, 12.5 × 15′ Rod mill, Allis-Chalmers 6 × 12 ft Rod mill, 6 × 12′ Rod mill, Allis-Chalmers 9 × 12 ft Rod mill, 9 × 12′ Rod mill.
The Ball / Rod / Compeb Rod mill is listed under the Allis Chalmers brand as: Rod mill. Period: 1965. Status: Historical model.
7 components are recorded, including: Ball Mill Shells, Ball Mill Heads, Ball Mill Trunnions, Shell liner, Ball Mill Main Bearings, Bearing Shells and Housings, Girth Gear (Ring Gear), Drive Pinion. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry