Hydraulic Cone crusher · 2025 · 8 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Hydrocone 22 in Cone crusher | 22″ Hydrocone | 2025 | 8 |
| 322R Hydrocone 22 in Cone crusher | 322 Type R; 22″ Reduction Crusher | 8 | |
| Hydrocone 36 in Cone crusher | 36″ Hydrocone | 2025 | 8 |
| Hydrocone 45 in Cone crusher | 45″ Hydrocone | 2025 | 8 |
| Hydrocone 51 in Cone crusher | 51″ Hydrocone | 2025 | 8 |
| Hydrocone 60 in Cone crusher | 60″ Hydrocone | 2025 | 8 |
| Hydrocone 72 in Cone crusher | 72″ Hydrocone | 2025 | 8 |
| Hydrocone 84 in Cone crusher | 84″ Hydrocone | 2025 | 8 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Mantle | Outside moving cone | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
| 2 | Concave | Fixed crushing surface in top shell | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
| 3 | Spider bushing | Around shaft in spider center | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
| 4 | Mainshaft sleeve | Shaft below spider | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
| 5 | Eccentric bushing | Between eccentric and shaft | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
| 6 | Pinion | Inner pinionshaft drive end | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
| 7 | Hydroset piston | Inside cylinder below mainshaft | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
| 8 | Dust seal ring | Dust interface under moving cone | Traditional inch-size Hydrocone design relationships; no assembly drawing for each size |
Models with the same components are grouped together; select a group to open its component table.
Models: Hydrocone 22 in Cone crusher, 322R Hydrocone 22 in Cone crusher, Hydrocone 36 in Cone crusher, Hydrocone 45 in Cone crusher, Hydrocone 51 in Cone crusher, Hydrocone 60 in Cone crusher, Hydrocone 72 in Cone crusher, Hydrocone 84 in Cone crusher
| No. | Component | Location |
|---|---|---|
| 1 | Mantle | Outer surface of the moving cone on the main shaft |
| 2 | Concave | Inner wall of the upper housing |
| 3 | Cross beam bushing | Main shaft support on the upper housing crossbeam |
| 4 | Main shaft protection bushing | Outer circumference of the main shaft |
| 5 | Eccentric Bushing | |
| 6 | Pinion | |
| 7 | Hydraulic adjustment piston | Hydraulic support assembly at the lower part of the main shaft |
| 8 | Dust seal ring | Dust seal at the lower part of the moving cone |
The Hydrocone Hydraulic Cone crusher covers 8 models: Hydrocone 22 in Cone crusher, 322R Hydrocone 22 in Cone crusher, Hydrocone 36 in Cone crusher, Hydrocone 45 in Cone crusher, Hydrocone 51 in Cone crusher, Hydrocone 60 in Cone crusher, Hydrocone 72 in Cone crusher, Hydrocone 84 in Cone crusher. Former and renamed designations are listed in the models table on this page.
The Hydrocone Hydraulic Cone crusher is also documented under these designations: Hydrocone 22 in Cone crusher, 22″ Hydrocone, 322R Hydrocone 22 in Cone crusher, 322 Type R, 22″ Reduction Crusher, Hydrocone 36 in Cone crusher, 36″ Hydrocone, Hydrocone 45 in Cone crusher, 45″ Hydrocone, Hydrocone 51 in Cone crusher, 51″ Hydrocone, Hydrocone 60 in Cone crusher, 60″ Hydrocone, Hydrocone 72 in Cone crusher.
The Hydrocone Hydraulic Cone crusher is listed under the Allis Chalmers brand as: Hydraulic Cone crusher. Period: 2025. Status: Historical model.
8 components are recorded, including: Eccentric Bushing, Pinion, Mantle, Concave, Cross beam bushing, Main shaft protection bushing, Hydraulic adjustment piston, Dust seal ring. The full list with locations is in the components table on this page.
Model-specific components with their own page: Mantle, Concave, Cross beam bushing, Main shaft protection bushing, Hydraulic adjustment piston, Dust seal ring (6 in total).
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry