Epiroc البرغي ec صخري التثبيت جهاز الحفر الطرازات, الأدوات و قطع الغيار| ANRANST

Official Epiroc Boltec E image showing the bolting unit, BUT 45 boom, feed, hydraulic lines, chassis and stabilizer areas.

Official Epiroc Boltec M image for identifying medium-section operation, the bolting unit, boom and optional mesh-handling area.

Official Epiroc Boltec S10 image showing the bolting unit, feed, piping, chassis and stabilizers of this small-section rig.

OEM equipment guide

Confirm Boltec, the COP Rock Drill, Bolting Unit and Support Method Before Selecting Parts

Boltec covers low-profile, small, medium and larger openings, with S/SG variants, Auto Bolt Reload and different bolt, resin and grouting systems. Bits, shank adapters, jaws, slides, pins, bushings, cylinders and seals vary with the full model, serial number, COP rock drill, MBU/LBU/ABR unit and installation process. This page focuses on models, structures, materials and checks directly relevant to wear parts and essential spares.

8 Model and installation combinations

1.8–13 m Published support-height range

1.5–6.0 m Published bolt-length range

12 Wear-part and essential-spare categories

Models and key specifications

Boltec Models, Support Range and Key Configurations

Models follow Epiroc's rock bolting rig catalogue. The table retains only section, bolt length, rock drill, bolting unit, battery and Auto Bolt Reload information relevant to part identification.

Series / Model	Opening Size and Application	Bolts / Key Dimensions	Rock Drill, Unit and Installed Configuration
Boltec S	Fully mechanized bolting rig for small to medium openings	Bolts 1.5–3.5 m; maximum boom reach height approx. 7 m	Confirm COP RR11 / RR14 and the bolting unit from nameplates
Boltec SL	Low-profile headings of 1.8–2.2 m	Height approx. 1.3–1.77 m; width approx. 2.48 m; weight approx. 12.8 t	COP 628; low-profile LBU bolting unit
Boltec M10 S	Medium openings; Smart series	Bolts 2.1–3.5 m; 10-bolt magazine	COP RR11, optional RR14; BUT 45 S / M
Boltec M10 SG	M10 battery-tramming version	Bolts 2.1–3.5 m; 10-bolt magazine	SG means Smart and Green; confirm the actual power supply used during drilling
Boltec E10 S	Larger openings; Smart series	Bolts 2.1–6.0 m; 10-bolt magazine	COP RR11, optional RR14; BUT 45 S / M
Boltec E10 SG	E10 battery-tramming version	Bolts 2.1–6.0 m; 10-bolt magazine	SG means Smart and Green; identify battery, charging and high-voltage parts by serial number
Boltec M10 / E10 Auto Bolt Reload	Automatic bolt-reloading system	Feed magazine: 8 bolts + onboard rack: 44 bolts; M10 2.4 m, E10 2.4 or 3.0 m	Confirm the installed combination of S / SG and M10 / E10
Boltec S10	Fully mechanized bolting rig for small openings	Suitable bolt lengths: 1.5–2.4 m	Confirm rock drill, bolting unit and chassis configuration from nameplates

Legacy or regional machines such as Boltec 235 still require service but should not be presented as current global catalogue models. Check their parts separately using the full model, serial number, COP and bolting-unit nameplates, and original catalogue.

Wear parts

Bits, Drill Strings, Rock-Drill Front Ends, Bolting Units, Feeds and Pivot Wear Areas

Material links support engineering selection of ANRANST replacement parts; they do not imply one OEM material across all Boltec machines. Confirm the choice using rock properties, impact, threads, grout medium, support method, failure mode, used-part inspection and drawing requirements.

Bolt-Hole Bits and Carbide Buttons

Rock-bolt Drill Bits & Carbide Buttons

Bits directly face impact, rotation, abrasion and flushing media. Check hole diameter, thread, face design, button layout, flushing, rock properties and COP RR11, RR14 or COP 628 configuration together.

تقييم المادة: قيّم درجات كربيد التنجستن للأزرار. يجب أن يوازن الجسم الفولاذي بين متانة الصدمات ومقاومة إجهاد الخيوط ومقاومة تآكل السطح. أكِّد الاختيار بناءً على القطعة الأصلية ورقم الكتالوج ونمط الفشل.

Tungsten carbide High-strength, tough alloy steel for drilling tools

Explore drill bits and cutting teeth →

Shank Adapters, Couplings, Rods and Guide Tubes

Shank Adapters, Couplings, Rods & Guide Tubes

The shank adapter transfers rock-drill impact and torque into the drill string; couplings, rods and guide tubes transmit energy and maintain hole direction. Check the rock drill, thread system, rod diameter, length, flushing hole, end geometry and wear location.

تقييم المادة: تتطلب أجزاء سلسلة الحفر عمومًا فولاذًا سبائكيًا مقاومًا للإجهاد ومعالجة حرارية مضبوطة وتقوية سطحية. إن هندسة الخيوط والتمركز والاستقامة ومتانة القلب لا تقل أهمية عن المادة نفسها.

Alloy steel for rods, shank adapters and couplings

Explore drill strings and heavy-duty assemblies →

Rock-Drill Front-End Guides, Splines and Flushing قطع الغيار المستهلكة

Rock-drill Front-head Guides, Splines & Flushing قطع الغيار المستهلكة

Front-end guides, splines, flushing passages and seals face high-frequency impact, rotary friction, water and rock dust. The machine image locates the area; confirm guide and chuck sleeves, seals and flushing parts from the COP nameplate and sectional drawing.

Material assessment: Check alloy steel, bearing materials or the original composite for guides and splined parts. Select flushing seals by pressure, medium, temperature, speed and groove geometry.

Alloy steel for impact drives and splines Flushing seals and engineering plastics

Explore guides, bearings and bushings →

Bolting-Unit Jaws, Centralizers and Magazine Guides

Bolting-unit Grippers, Centralizers & Magazine Guides

Jaws, centralizers, rotary heads, bolt feeders and magazine guides repeatedly handle rods, bolts and plates under impact, off-center loads, rock dust and grout exposure. Confirm the MBU, LBU, ABR or S10 unit, bolt type, length and position.

Material assessment: Assess strong, tough alloy steels and local surface strengthening for gripping and load-transfer parts. Check guides, slides and scrapers as steel, copper-alloy or wear-resistant plastic friction pairs.

Alloy steel for gripping and load transfer Guide and sliding-support materials Wear-resistant engineering plastics

Explore gripping parts, pins and connections →

Feed Slides, Guides, Wear Strips and Thrust Blocks

Feed-beam Slides, Guides, Wear Strips & Thrust Blocks

The feed supports reciprocating motion of the rock drill and bolting unit. Slides, guides, wear strips and thrust blocks face off-center loads, rock dust, flushing water and grout contamination. Check the feed section, stroke, hole spacing, clearance and wear reference.

تقييم المادة: قيّم البلاستيك الهندسي المقاوم للتآكل أو سبائك النحاس أو الفولاذ المقسّى للأجزاء المنزلقة. تتطلب الأدلة الحاملة والأشرطة المقاومة للتآكل أيضًا فحوصات للصلابة والصدمات وزوج الاحتكاك المتزاوج والتزييت في الموقع.

Wear-resistant engineering plastics and sliding composites Copper alloys for sliding supports Quenched-and-tempered wear plate

Explore guides, wear strips and plates →

Wear Pairs at Boom, Mesh-Handler and Stabilizer Pivots

Boom, Mesh-handler & Jack Pivot Wear Pairs

Pins, bushings, thrust parts and telescopic guides in the boom, optional mesh handler and stabilizers face alternating bending, impact and sliding wear. Check BUT 45 or the specific arm, left/right position, shaft diameter, length, lubrication grooves, housing bore and clearance.

Material assessment: Assess strong, tough alloy steels and surface strengthening for pins. Bushings follow the original copper-alloy, bearing-steel or sliding-composite design; hardness alone cannot replace complete fit verification.

Alloy steel for pins and load-bearing connections Bushing and plain-bearing materials

Explore pins, bushings and connections →

Spare parts

Essential Rock-Drill, Bolting, Grouting, Boom, Chassis and Hydraulic Spares

Drive, support and seal parts are listed separately. S, SL, M10, E10, S10, S/SG and ABR configurations differ in bolting units, chassis, hydraulics, electrics and controls. Identify spares against the full model, serial number, assembly nameplate and installation position.

COP RR11, RR14 and COP 628 Rock-Drill Assemblies

COP RR11, RR14 & COP 628 Rock-drill Components

Boltec models use COP RR11, RR14 or the low-profile COP 628. Shank adapters, front ends, percussion pistons, rotation, bearing, flushing and seal interfaces vary by rock drill. Provide the complete COP nameplate or assembly number.

تقييم المادة: قيّم فولاذ السبائك المقاوم للإجهاد والهندسة السطحية لمكابس الطرق والأخاديد المحززة وأنظمة الدوران. أكِّد المحامل والجلبات والأختام وأجزاء التنظيف وفقًا للبنية الأصلية والتفاوتات والوسط والظروف الحرارية.

Alloy steel for rock-drill percussion and drives Flushing and hydraulic seal materials

Explore rock drills and heavy-duty assemblies →

MBU/LBU Bolting Units and Auto Bolt Reload

MBU/LBU Bolting Units & Auto Bolt Reload

Bolting units include magazines, clamps, feeders, rotation, plate handling and travel-limit parts. ABR also includes a feed magazine and onboard storage for 44 bolts. Confirm M10, E10, S, SL, S10, S/SG, bolt type and length.

Material assessment: Assess drive alloy steels for gears, shafts, pins and gripping parts. Check slides, bushings and seals for friction, contamination, grout medium and original fits. Safety interlocks must retain their original functional rating.

Alloy steel for drive shafts, gears and gripping parts Bushing and sliding-support materials

Explore bolting units and heavy-duty assemblies →

Pumps, Valves and الموانع for Resin, Grout and Cement Systems

Resin, Grout & Cement-system Pumps, Valves & الموانع

Pumps, metering devices, mixers, valves, hoses, nozzles and seals are not interchangeable between resin-cartridge insertion, pumpable resin, SDA/hollow-bolt grouting and automatic cement systems. Specify the medium, mix ratio, pressure, flow, temperature and cleaning method.

Material assessment: Select stainless steel, wear-resistant steel or polymers for wetted parts according to corrosion and abrasion from resin, cement slurry, water and cleaning media. Confirm seals, hoses and scrapers for chemical compatibility, pressure and temperature.

الموانع and engineering plastics for resin/grouting systems Corrosion- and wear-resistant alloys

Explore pump/valve seals and engineering materials →

Boom, Feed and Stabilizer Cylinders and Connections

Boom, Feed & Jack Cylinders with Connections

The BUT 45 boom, feed, stabilizers and mesh handler use multiple cylinders, pins, bushings, hoses and position-feedback parts. Check cylinder assembly number, bore, rod diameter, stroke, end connections, left/right position and sensors.

Material assessment: Check rods, barrels and pins for alloy-steel strength and toughness, surface quality and dimensions; seals for pressure, speed, temperature, medium and grooves; welded structures for the original process and nondestructive inspection requirements.

Alloy steel for cylinders, pins and load-bearing parts Hydraulic seals and guide materials

Explore cylinders, pins and connections →

Axles, Brakes, Hubs and Final Drives

Axles, Brakes, Wheel Hubs & Final Drives

Axles, brakes, hubs, drive shafts, differentials and final drives operate on gradients amid damp rock dust and frequent starts and stops. S, SL, M10, E10, S10 and battery-tramming variants have different chassis and tires. Confirm parts from the axle nameplate and assembly number.

تقييم المادة: قيّم فولاذ الإدارة السبائكي وتقوية سطح الأسنان للتروس وأنصاف الأعمدة والمحاور المحززة وأعمدة الإدارة. افحص المراكز والمحامل والفرامل والأختام وفقًا لتفاوتات التجميع الأصلية والتزييت ومتطلبات ارتفاع الحرارة.

Alloy steel for axles, gears and drive shafts Wheel-end and brake seal materials

Explore gears, shafts and final drives →

Hydraulic, Water, Air, Cable and S/SG Control Components

Hydraulic, Water/Air, Cable & S/SG Control Components

Pumps, valve blocks, accumulators, water pumps, flushing valves, filters, coolers, cable reels, sensors and control modules support drilling and bolt installation. Interfaces differ between S/SG, RCS, ABR and grouting systems.

Material assessment: Check precision pump/valve parts and connections against original dimensions, tolerances and surfaces. Select seals for medium, pressure, temperature, speed and contamination. Controls must match voltage, protocol, software version and safety rating.

Water, air and hydraulic seals and engineering plastics Alloy steel for pumps, shafts and connections

Explore hydraulic seals and control components →

Drawing and Spare-Part Numbers

Match Every Number to Boltec, the COP Rock Drill, Bolting Unit and Location

The available Epiroc reference records do not contain publishable OEM numbers with verified two-way matches to specific Boltec models. No placeholder numbers are listed. Submit an Epiroc OEM or third-party number, COP/MBU/LBU/ABR assembly number, catalogue page, used-part marking and critical dimensions for a lookup.

Submit an Epiroc OEM or Assembly Number Check Boltec, serial number, COP, bolting unit, support system and position. Submit a Third-Party Part Number Link the supplier, equipment, assembly, part, dimensions, material and original number. Submit a Drawing, Catalogue Page, Nameplate or Used Part Where no reliable number exists, assess catalogue lookup, sample inspection or dimensional measurement.

Reference policy: Only references traceable to an OEM catalogue, drawing, nameplate or reliable third-party match are published. For drilling tools, check thread, hole diameter and rock drill; for bolting units, MBU/LBU/ABR, bolt and grouting method; for chassis and hydraulics, the assembly nameplate.

Are Boltec drilling tools and bolting-unit parts interchangeable by series alone?

No. Confirm the full model, serial number, COP rock drill, thread and hole diameter, MBU/LBU/ABR unit, bolt length and type, resin/grouting system and installation position together.

What information is needed for a Boltec spare-parts enquiry?

Provide the full model and serial number, S/SG version, COP and bolting-unit nameplates, bolt and grouting method, OEM/third-party reference, used-part photographs, critical dimensions, current material and failure details.

هل يمكن تحديد القطعة دون رقم من الشركة المصنعة الأصلية Epiroc؟

Submit machine, COP and bolting-unit nameplates, catalogue pages, used-part markings, photographs, critical dimensions and drawings. These establish whether catalogue lookup, sample inspection or measurement is feasible. We do not invent references or interchangeability without reliable evidence.

Epiroc طرازات منصات التثبيت الصخري Boltec وأدواتها وقطع غيارها الأساسية