Can a part be identified without an Epiroc OEM number?

The equipment can be submitted with the generic nameplate, catalog pages and car or bridge logos; old-fashioned marking of items. Photographic data may also indicate whether it is possible to reverse a catalogue inspection as well for sampling purposes in order not either by numbering nor interchangeable relationships when there are no reliable evidence available."

Epiroc Minetruck تحت الأرض الشاحنات: الطرازات| ANRANST

Official Epiroc Minetruck MT65 S image showing the dump body, chassis, articulation, axles, power compartment and external guards.

Official Epiroc Minetruck MT54 S image showing the body, hoist, articulation, axles and power compartment of a large diesel truck.

Official Epiroc Minetruck MT42 SG image identifying the battery-electric configuration; batteries, motors, charging equipment and high-voltage systems require model-specific confirmation.

OEM المعدات التفاصيل

Confirm the Minetruck model, serial number, body and powertrain before selecting parts

The current Minetruck range covers underground haulage from 22 to 66 t, including conventional diesel, low-profile, battery-electric, trolley-assisted and diesel-electric configurations. At the same payload rating, body, hoist, articulation, axle, transmission, hydraulic and control configurations can differ with the full model, serial number, ore density, regional version and installed options. This page covers the models, dimensions, materials and identification details relevant to wear parts and core spares.

11 Current Standard Models Entrance

22–66 t Official Current Rated Load Scope

4 Diesel, battery packs and wired ducting

12 قطع الغيار المستهلكة and Key Spare Part Categories

Standard Models and Key Dimensions

Minetruck models, rated payloads and key dimensions

The table follows the Epiroc underground truck catalogue and lists information relevant to vehicle and spare-part identification. Body capacity varies with ore density and configuration. Confirm the complete model, serial number and body number before requesting a quotation.

Series / model	Rated payload	Powertrain / application	الأبعاد الرئيسية / configuration checks
Minetruck MT22	22 t	Diesel; small and medium underground haulage	Approximate empty weight: 23.3 t; formerly designated MT2200
Minetruck MT33	33 t	Diesel; medium underground haulage	Confirm the complete model, serial number and body configuration
Minetruck MT431B	28.1 t	Diesel; medium and large underground haulage	Body configuration depends on ore density and drift cross-section
Minetruck MT436B	32.6 t	Diesel; medium and large underground haulage	Confirm body, powertrain and axles against the serial number
Minetruck MT436LP	32.6 t	Low-profile diesel	For low-profile applications with roof heights down to approximately 2.3 m
Minetruck MT42 S	42 t	Diesel; Smart series	Standard body approximately 19.0 m³; confirm the configuration for the material density
Minetruck MT54 S	54 t	Diesel; large underground haulage	Confirm body, powertrain and installed options against the serial number
Minetruck MT65 S	65 t	Diesel; large underground haulage	Approximate empty weight: 46.3 t; body capacity: 27–40.4 m³, depending on material density
Minetruck MT66 S eDrive	66 t	Diesel-electric; Smart series	Body: 40 m³; empty weight: 43 t; width: 3,500 mm; length: 11,447 mm
Minetruck MT42 SG	42 t	Battery-electric; Smart and Green	Standard body: 19.0 m³; empty weight including battery: 37.7 t; usable battery energy: 465 kWh
Minetruck MT42 SG Trolley	42 t	Battery-electric with trolley power supply	Trolley operation and dynamic charging on ramps; confirm body and installed equipment for the project

The Epiroc catalogue lists MT431B, MT436B and MT436LP alongside MT42 S, MT54 S, MT65 S, MT66 S eDrive, MT42 SG and MT42 SG Trolley. Payload alone does not establish interchangeability between regional versions or older installations.

قطع الغيار المستهلكة

Body liners, discharge edges, underbody guards and pivot wear parts

Material links support engineering screening for ANRANST replacement parts. They do not imply that every Minetruck uses the same OEM material. Confirm ore density, particle size, loading drop height, haulage cycle, failure mode, worn-part inspection and drawing requirements.

Dump-body floor and main impact-zone liners

Dump Box Floor & Main Impact-zone Liners

The floor is exposed to loading impact, ore pressure and sliding wear during discharge. The illustration identifies a general part category, not an interchangeable Epiroc OEM part. Confirm the Minetruck model, body number, material density, panel position, thickness, holes and welding boundaries.

Material selection: Balance impact resistance, resistance to denting and abrasion resistance. Assess quenched-and-tempered wear plate or a suitable composite wear structure; hardness alone is insufficient.

Quenched and Tempered Wear Plate السبائك المتخصصة and Composite Wear-Resistant Materials

Entrance Liners, the collage board and wear-resistant plate unified page -

Body side, front and corner liners

Dump Box Side, Front & Corner Liners

Sidewalls, front plates and corners face lateral ore pressure, sliding abrasion and local impact. Wear can vary with loading practice and particle size. Confirm left/right position, curvature, joints, stiffeners, mounting method and the wear pattern on the old part.

Material selection: Assess quenched-and-tempered wear plate for bent panels. Tough cast steel, composite plate or local reinforcement may suit high-impact corners and concentrated wear zones.

Quenched and Tempered Wear Plate Specialized Wear-Resistant Alloys

Enter the car Liners and Construction Abrasion boards single page

Tailgate, spill-guard and discharge-edge wear parts

Tailgate, Spill Guard & Discharge-edge قطع الغيار المستهلكة

Some configurations use a tailgate or spill guard. Discharge edges, pivots and contact surfaces experience impact, trapped material and repeated opening loads. Confirm the body option, pivots, cylinders or linkage, cutting edges and sealing contact surfaces.

Material selection: Assess tough wear-resistant steel plate for discharge edges. Check pins, bushings and load-bearing pivots against their alloy-steel or bearing-material requirements while retaining the specified running clearances.

Quenched and Tempered Wear Plate Reflection Points pins Supplies and Containers alloy steel bushings Copper alloys with sliding braces

Enter the unloading edge, scaffold and wear-resistant board unified page -

Underbody, belly guards and impact protection plates

Underbody, Belly Guards & Impact Protection Plates

Road contact, falling rock and mine slurry wear the replaceable guards beneath the chassis, power compartment, axles, tanks or electric-drive system. Confirm the model, powertrain version, mounting position, bends, holes and maintenance access.

Material selection: Assess high-strength, tough wear plate. Guards near oil lines, batteries or high-voltage components must retain the original clearances, insulation and collision-protection requirements.

Quenched and Tempered Wear Plate

Entrance Protection PCBs and Construction wear parts Unified Pages

Mudguards, wheel guards and external protection

Mudguards, Wheel Guards & External Protection

External guards face material thrown by tyres, slurry, contact damage and vibration fatigue. Illustrations identify the category only. Confirm axle position, left/right orientation, tyre size, brackets, bends, holes and movement clearances.

Material selection: Assess formable high-strength steel or wear plate, including bend radius, weld fatigue, bracket stiffness and maintenance access.

Highly Strong wear-resistant steel plate

Enter the car hygrom and sheeting page -

Articulation, suspension and dump-body pivot wear pairs

Articulation, Suspension & Dump-body Pivot Wear Pairs

Pins, bushings and thrust components in articulation, front-axle suspension, steering and body-hoist pivots face impact, oscillation and boundary lubrication. Identify the exact pivot and provide shaft diameter, length, lubrication grooves, retention details, housing bore and clearances.

Material selection: Assess tough alloy steel and surface hardening for pins. Select bushings against the specified copper alloy, steel-backed composite or original bearing material, taking lubricant contamination and housing-bore repair into account.

pins Supplies and Containers alloy steel bushings With sliding Copper Alloys for Bearings

Entrance pins, bushings Unified Pages with Slip Bearing -

قطع الغيار

Hoist, articulation, transmission, axle, hydraulic and electric-drive spares

Transmission, support and hydraulic parts are listed separately. Diesel trucks, MT42 SG, MT42 SG Trolley and MT66 S eDrive have different power and control systems. Identify spares by the complete model, serial number, assembly nameplate, installation position and drawing.

Hoist cylinders, dump-body pivots and linkage

Hoist Cylinders, Dump-body Pivots & Linkage

The hoist system includes cylinders, cylinder pins, main body pivots, bushings, thrust parts, linkage and hydraulic connections. Provide body configuration, cylinder identification, bore, rod diameter, stroke, end connections, pivot positions and assembly orientation.

Material selection: Check cylinder rods, pins and links against alloy-steel and surface-treatment requirements. Confirm bushings and seals for load, oscillation, pressure, speed, temperature, contamination and original groove dimensions.

Tank poles, pins Supplies and Containers alloy steel bushings With sliding sliding materials Hydraulic sealing and Guiding materials

Entrance pins, Connections and Working Tank Part / Assembly Pages -

Centre articulation, steering cylinders and front-axle suspension

Center Articulation, Steering Cylinders & Front-axle Suspension

The front and rear frames steer through the central articulation; some models also have front-axle suspension. Check main pins, bushings, thrust parts, steering and suspension cylinders, accumulators and stops against the exact pivot, orientation, clearances and pressure requirements.

Material selection: Check tough alloy steel and surface hardening for pins and trunnions, and the original copper-alloy or composite specification for bushings. Confirm hydraulic parts as a system, including pressure, stroke, connections and seals.

Reflection pins Supplies and Containers alloy steel Reflection bushings With sliding bearing materials Suspension and steering hydraulic sealing

Entrance bearing, bushings Unified Pages with Hosting -

Diesel engine, torque converter, transmission and drive shafts

Diesel Engine, Converter, Transmission & Drive Shafts

On diesel trucks, the engine, torque converter, transmission, shafts and couplings transmit torque to the axles. The image illustrates the general category, not Epiroc interchangeability. Confirm the vehicle model, serial number, engine and transmission nameplates, splines and flanges.

Material selection: Assess carburised, quenched-and-tempered or induction-hardened transmission alloy steel for gears and shafts. Confirm housings, bearings and couplings for load, alignment, lubrication, temperature rise and vibration.

gear, Clock shafts and Alloy Steels for Drive Parts

Entrance gear, pinion, Axle and Connector Unified Pages -

Axles, differentials, wheel ends and wet brakes

Axles, Differentials, Wheel Ends & Wet Brakes

Axles include final drives, differentials, half shafts, wheel reductions, hubs, bearings, seals and wet brakes. The image does not identify an Epiroc OEM part. Check axle nameplate, ratio, tooth count, splines, left/right wheel position and brake-pack specification.

Material selection: Select gear and shaft materials against contact and bending fatigue. Brake friction pairs, bearings and seals require confirmation of the original assembly, fluid, temperature, clearances and safety requirements.

Bridges, gear With the semi-axis alloy steel Wheelside and Brake Seal Materials

Entry to the bridge, shafts and reloading Power Transmission Part / Assembly Pages -

Hydraulic pumps, valves, hoses, cooling and seals

Hydraulic Pumps, Valves, Hoses, Cooling & الموانع

Hoist, steering, braking, suspension and auxiliary circuits use pumps, valve assemblies, accumulators, hoses, fittings, coolers and seals. Provide circuit location, pump and valve nameplates, pressure, flow, connections and hose specifications.

Material selection: Preserve original dimensions, tolerances and surface requirements for precision parts and fittings. Select seals for fluid, pressure, temperature, speed, contamination and groove geometry, not outside diameter or colour alone.

Hydraulic الموانع and Engineering Plastics Valve cores, shaft and connector alloy steel

Entering hydraulic الموانع and Engineering Materials Unified Pages

Battery, trolley, diesel-electric drive and controls

Battery, Trolley, Diesel-electric Drive & Controls

MT42 SG, MT42 SG Trolley and MT66 S eDrive have different power systems: battery and traction motor, pantograph and trolley interface, or generator, DC bus and wheel motors. Confirm the specific model, serial number, voltage rating, controls and software version.

Material selection: Check mechanical shafts and couplings against transmission-alloy requirements, and cooling or hydraulic seals against fluid and temperature. High-voltage parts must retain the original ratings, connections, insulation, certification and control version; matching appearance is insufficient.

Mechanical Power Transmission axis with motor alloy steel Cooling, seal and insulation engineering materials

Entry power and reload Part / Assembly Unified Pages

Drawing and Spare Part Numbers

Match part numbers to the truck, body, powertrain, assembly and installation position

No publicly traceable OEM part number in the available records has yet been matched in both directions to a specific Minetruck model. Submit the Epiroc or third-party number, body number, axle or transmission nameplate, catalogue page, worn-part marking and key dimensions for identification.

Submission Epiroc OEM Node or total number Converged Minetruck, serial number wagons, powertrain and general installation position Submission to third parties spare parts No Establishment of the company, المعدات, parts Scales, materials Relatives to the original number Submitting drawings, catalog pages nameplate Or old ones Conducting a catalog retrospective, sample detection or mapping evaluation without reliable number

متطلبات التحديد: Use numbers traceable to an OEM catalogue, drawing, nameplate or reliable cross-reference. For body parts, also confirm body number, material density, panel position and side. For transmission, axle, hydraulic and electric-drive parts, confirm the assembly nameplate and installed version.

Are Minetruck liners and transmission parts interchangeable at the same payload?

No. Check the full model, serial number, body number, ore density, powertrain version, axle and transmission nameplates, assembly number, installation position and key dimensions.

What information is needed for a Minetruck spare-parts enquiry?

Provide the full model and serial number, powertrain version, body number and panel position, axle or transmission nameplate, OEM or third-party number, worn-part photographs, key dimensions, current material and failure details.

هل يمكن تحديد القطعة دون رقم من الشركة المصنعة الأصلية Epiroc؟

Submit equipment and assembly nameplates, catalogue pages, body or axle identification, worn-part markings, photographs, dimensions and drawings. These establish whether catalogue matching, sample inspection or measurement is feasible. Part numbers and interchangeability must not be invented.

Epiroc Minetruck Underground Trucks: Models, Body قطع الغيار المستهلكة and Core Spares