Protection plates, pans & wear plates
الحماية ألواح, صواني المغذي و الهيكلية ألواح التآكل
Carry material, absorb impact, guide flow and protect equipment structures
These components are more than a piece of steel plate. Apron feeder pans form a continuous load-bearing surface. Crusher protection plates shield frames, swing jaws and feed structures. VSI internal wear plates resist high-speed particle wear. Industrial feed plates and trash plates also stabilise or guide the material bed.
Load carrying and conveying Apron feeder pans and falling-material impact plates
Structural protection Jaw crusher cheek plates, swing jaw protection plates and cone crusher frame guards
High-speed wear Wear plates around VSI rotors and inside the chamber
متطلبات التحديد المعدات, position, orientation, interfaces, drawing reference, material and wear pattern
Category scope
تحديد المعدات OEM, complete model, serial number and structural version
Installation interfaces Position, handedness or upper/lower location, orientation, adjacent parts, overlap and interfaces
Plate geometry Profile, thickness, holes, counterbores, ribs, rear support and wear allowance
ظروف التشغيل Loads, impact, abrasion, temperature, material flow direction and replacement interval
Identify by function and installation relationships
Mantles, concaves, jaw plates and mill liners that directly form crushing or grinding surfaces belong to Industrial liners and wear linings; components with openings or slots for screening or discharge belong to screen panels, grates and screen media.
This page covers load carrying, falling-material impact, structural protection, material guidance and local wear plates. Each component still requires equipment identification, installation position and part number. Similar appearance does not establish interchangeability between machines.
Apron Feeder
Feeder pans and impact-bearing components
Pans form a moving load-bearing system and must be checked with chains, sprockets, support rollers and skirt boards.
Apron feeder pans
Multiple pans connect to chains and overlap to form the carrying surface. Check width, side height, overlap, raised ribs, chain-link hole spacing and drive direction.
Falling-material impact plates
Fit below bins or in concentrated drop zones to distribute impacts from large material pieces. Check drop height, support, cushioning, fastening and adjacent skirt boards.
Crusher structural protection
Jaw, cone and VSI crusher protection plates
These plates protect costly structures or stabilise material flow. They do not replace the actual crushing surfaces.
Jaw crusher upper cheek plates
Protect the upper chamber frame sidewalls. Distinguish left, right and upper positions; check jaw plate profile, clamps, holes and sidewall contact.
Jaw crusher lower cheek plates
Protect discharge-end sidewalls under continuous abrasion from finer material. Match upper cheek plates, fixed and movable jaw plates, and the discharge opening.
Swing jaw protection plates
Separate material from the front swing jaw casting to prevent direct wear of the costly structure. Check profile, support, holes and space behind the jaw plate.
Jaw crusher intermediate plates
Provide jaw plate fit or protection in specific designs. Confirm whether fitted, thickness and holes against model and drawings.
Cone crusher frame arm guards
Protect frame arms and adjacent structures from falling material, flying rock and discharge erosion. Check arm position, curved surfaces, handedness and fastening orientation.
Cone crusher main frame liners
Protect the main frame casting below the crushing chamber. Check segments, discharge direction, adjacent arm guards and installation clearances.
Cone crusher feed plates and cones
Distribute feed into the chamber and protect the upper crushing head. Check central mounting, rotation direction, feed distribution and locking structure.
VSI upper internal wear plates
Protect upper rotor or chamber areas exposed to high-speed material flow. Check rotor type, upper/lower position, rotation direction, adjacent wear parts and particle trajectories.
Industrial feeding and material guidance
Sugarcane mill feed plates and trash plates
These components control the material bed and crushing-roll inlet. Mining crusher guards are not substitutes.
Feed roller feed plates
Guide cane or bagasse into the crushing rolls and stabilise the material bed. Check roll arrangement, plate curvature, clearance, fastening and corrosive wear.
Trash plates and bars
Support and guide material between rolls. Check mill dimensions, roll centre distances, working-surface curvature, clearance and wear layer.
المواد والعمليات
Balance materials differently for load carrying, impact, abrasion and protection
Determine final grades and heat treatment only after equipment, position and failure evidence are clear.
Failure and identification
Use bending, cracks, uneven wear and looseness to investigate the structure
Plate problems commonly involve support, connections, material flow and installation orientation together.
| Symptoms | الفحوصات ذات الأولوية | Associated Risks |
|---|---|---|
| Pan bending or fracture | Falling-material impact, support rollers, thickness and ribs, chain-link holes, material toughness and overload | Failed overlap, material leakage and uneven chain loading |
| Elongated holes or loose bolts | Hole spacing, counterbores, contact faces, preload, plate movement and adjacent overlap | Detached guards and wear to the protected structure |
| Local cheek plate wear-through | Left/right and upper/lower position, jaw tooth profile, biased feed, discharge opening and clamping | Direct wear of frame sidewalls |
| Chipped edges or cracks in guards | Peak impact, material toughness, abrupt section changes, unsupported voids and heat treatment | Fragments entering downstream equipment or damaging adjacent parts |
| Uneven VSI wear plate wear | Rotor balance, rotation direction, feed distribution, adjacent rotor tips and cascade or rock-on-rock condition | Rotor imbalance and abnormal vibration |
| Unstable material bed on the feed plate | Working-surface curvature, clearance, roll positions, surface wear and material condition | Reduced throughput and less stable loading and product quality |
Enquiries and quality control
Plate supply information
A two-dimensional outline is only a starting point. Include installation and support relationships.
المعدات والموضع
OEM, complete model, serial number, installation area, handedness or upper/lower position, rotation direction and adjacent parts.
مراجع الرسم والهندسة
Part number, drawing revision, profile, thickness, hole spacing, counterbores, ribs, curved surfaces and wear allowance.
Connections and support
Chain links, bolts, welding, overlap, backing plates, cushioning, support faces and assembly clearances.
المواد والعمليات
Casting or plate stock, chemical composition, heat treatment, mechanical properties, hardness, welding and surface protection.
ظروف التشغيل وأنماط الأعطال
Loads, drop height, material, particle size, abrasion, temperature, uneven wear, cracks, deformation and service life.
Inspection and complete sets
Material traceability, dimensions, non-destructive testing, hardness, templates or trial assembly, position markings and fasteners.
Technical references: Metso treats apron feeder pans as heavy-duty load-bearing and wear components, emphasising original drawings and compatibility with overlap, chains and support systems. Its jaw crusher parts information identifies cheek plates as frame sidewall protection.Metso Apron Feeder Parts · Metso Jaw Crusher Parts
الأجزاء والمعدات ذات الصلة
Shared product pages for general equipment and OEM models
المعدات relationships explain function, OEM relationships establish complete models and drawing references, and material relationships define manufacturing and acceptance requirements.
Apron Feeder Pans, chains, sprockets, support rollers and skirt systems. Jaw Crushers Cheek plates, swing jaw protection and feed structures. Industrial Liners Distinguish protection plates from surfaces directly involved in crushing or grinding. العلامات التجارية والموديلات الأصلية Identify dedicated plates by brand, series, complete model and part number.
Request a quotation for protection plates, feeder pans and structural wear plates
Submit equipment models, installation positions, drawing references, used-part dimensions, materials and wear records for technical and supply review.
خدمات صنع في الصين
من التقييم الفني إلى تسليم المنتج بالكامل
توفر شركة ANRANST للعملاء العالميين تقييمات هندسية، واختيار التصنيع الصيني، ومراقبة الجودة، وتسليم الأجزاء النهائية لقطع الغيار الصناعية المقاومة للتآكل حسب الطلب، ويمكنها أيضًا دعم قطع الغيار الصناعية الأخرى حسب الطلب.
مراجعة الرسومات والهندسة
قم بمراجعة أسطح التزاوج وأبعاد الواجهة، وقم بتقييم جدوى المواد والمعالجة الحرارية والتصنيع.
تحديد المادة والمعالجة الحرارية
تُحدَّد درجات المواد وعمليات المعالجة الحرارية لكل طلب على حدة، وتُثبَّت في الاتفاقية الفنية وتُتابَع أثناء الإنتاج.
ضبط الجودة
يشمل ذلك تأكيد الرسم، ومراقبة المواد والعمليات، وتتبع الإنتاج، وتنسيق عمليات الفحص والقبول.
تسليم المنتج النهائي
تنظيم عمليات التصنيع والتحقق من الجودة والتعبئة والتغليف وتسليم المنتجات النهائية الكاملة لتشكيل حلقة إمداد قابلة للتنفيذ.
قم بتزويدنا بالنماذج الحالية، والرسومات، وأرقام الرسومات، وأرقام الأجزاء، والمواد، أو معلومات ظروف التشغيل، وسنقوم بتحديد التحقق الفني ومسار التوريد وفقًا لذلك.
إرسال طلب