Start with the brand, equipment series and installed machine, then explore wear parts, drive and structural spares, materials and processes, drawing review, quality control and finished-part delivery.
This page covers equipment series and models, part locations, materials and processes, drawing review and inquiry options. Before manufacture or quotation, confirm drawing, dimensions and tooling suitability against the complete model and drawings.
The model table assists with machine identification. Manufacture and quotation require the nameplate, complete model, serial number, drawing, general arrangement and drawing revision.
| Series / Model | Equipment Range and Identification | Equipment History and Identification |
|---|---|---|
| Medium-Speed Coal Mill | Use the complete model, serial number, drawing and general arrangement together to identify the installed equipment | Identify the installed machine from its equipment records |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Feed conveyor | Lateral feed conveyor at the upper right (original 1) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 2 | Grinding table | Rotating grinding table below the rollers (original 2) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 3 | Grinding roller | Red grinding roller in the grinding chamber (original 3) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 4 | Hydraulic roller spring assembly | Hydraulic loading assembly at the lower left (original 4) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 5 | Louvre ring | Louvre ring surrounding the grinding table (original 5) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 6 | Hot-gas passage | Hot-gas passage below the table towards the louvre ring (original flow marker 6) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 7 | Classifier | Built-in LSKS classifier in the upper section (original 7) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 8 | Internal grit return cone | Grit return cone beneath the classifier (original 8) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 9 | Product-and-gas outlet duct | Product and process-gas outlet duct at the upper left (original 9) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
| 10 | Vertical gearbox | Red vertical gearbox beneath the grinding table (original 10) | Brochure configuration: four-roller modular solid-fuel mill and LSKS classifier; not all LM D sizes/roller counts covered |
These general Medium-Speed Coal Mill part categories help identify the part you need. Confirm suitability against the specific LOESCHE model and drawings.
Grinding Ring / Bowl Liner
A general wear part category for Medium-Speed Coal Mill equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Classifier Blade / Vane
A general wear part category for Medium-Speed Coal Mill equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Classifier Cone Liner
A general wear part category for Medium-Speed Coal Mill equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Mill Housing Liner
A general wear part category for Medium-Speed Coal Mill equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Inlet Duct Liner
A general wear part category for Medium-Speed Coal Mill equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →Identify gears, shafts, sleeves, bearings, seals, hydraulic parts, supports and connectors for drawing review. Listed OEM drawing or part references relate to identified parts and require confirmation against your machine.
Roller Shaft Bearing
A general structural or drive part category for Medium-Speed Coal Mill equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Journal Bearing
A general structural or drive part category for Medium-Speed Coal Mill equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Seal Air Nozzle
A general structural or drive part category for Medium-Speed Coal Mill equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →Provide the complete model, serial number, drawing revision, installation position, photographs of the current part, material and operating conditions.
No. General images help identify the part category. Manufacture requires agreed drawings, dimensions, interfaces, materials and acceptance criteria.
Start with the nameplate, general arrangement drawing, installation position, used-part photographs and key dimensions. We can then assess the feasibility of dimensional inspection, material evaluation and manufacture to drawing.
Provide the complete model, serial number, nameplate, installation position, photographs of the current part, drawings, material and operating conditions. We use these to identify the part, assess materials, organize production at certified foundries, coordinate quality control and arrange finished-part delivery.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry