TAKRAF X-TREME Class الغرابيل المقطعية, قطع التآكل والغيار| ANRANST

TAKRAF product gallery: TCS-X 14.35 primary sizer, locating twin rolls, frame, drive and feed/discharge systems.

TAKRAF product gallery: secondary-sizer teeth, providing a reference for tooth profiles, segments and fixing positions.

TAKRAF product gallery: TCS 12.24 installed in a transfer tower. Confirm the configuration against the project general arrangement.

OEM المعدات Reference

Use standard 06–18 Series to identify segments, bearings and drive spares

TAKRAF X-TREME Class sizers use two counter-rotating rolls for hard-rock sizing. The current range covers primary, secondary and tertiary duties. Teeth, segments, shafts, bearings, seals, drives and frames vary with series, material, project configuration and maintenance history. Confirm full model, serial number, drawing number and actual interfaces before manufacture.

06–18 Series Current published product series

Up to 2,600 mm Manufacturer-published maximum feed size

100–14,000 t/h Manufacturer-published capacity range

Up to 280 MPa* Manufacturer-published rock-strength range

Standard Models and Key Dimensions

Standard series, key dimensions and throughput ranges

The table follows current TAKRAF information for 06, 08, 12, 14 and 18 Series roll centres, typical feed/product sizes and throughput. It identifies machine families and is not a spare-part interchangeability table without drawing confirmation.

Standard series	Roll centre distance	Typical feed / product size	Typical throughput
06 Series	620 mm	Feed 125–400 mm; product 40–150 mm	Up to 2,500 t/h
08 Series	790 mm	Feed 250–600 mm; product 50–150 mm	Up to 4,000 t/h
12 Series	1,050 mm	Feed 600–1,200 mm; product 150–350 mm	Up to 6,000 t/h
14 Series	1,300 mm	Feed 800–1,400 mm; product 250–350 mm	Up to 10,000 t/h
18 Series	1,550 mm	Feed 1,200–2,500 mm; product 350–450 mm	Up to 14,000 t/h

* Rock strength up to 280 MPa requires testing by TAKRAF Minerals Laboratory. Published TCS-X 14.35, TCS-X 08.30 and TCS 12.24 projects are installation references only; compatibility requires full model, project or serial number, roll construction and drawing revision.

قطع الغيار المستهلكة

Identify teeth, replaceable segments and chamber liners

Teeth, segments and liners are the main wear parts. Manufacturer pages confirm quick-connect segments and bolt-on primary teeth, but do not publish a complete order-ready drawing or material-grade list. Materials and dimensions require actual conditions, drawings and used-part checks.

Crushing Teeth and Tooth Segments

Crushing Teeth & Tooth Segments

Provide crushing, gripping and product-size control on twin rolls. Check profile, pitch, segment position, fastening, working-face wear, material strength, abrasiveness and removal direction. Manufacturer images locate components only.

Material selection: The manufacturer describes wear-material technology without publishing specific grades here. Select materials against impact, abrasion, segment construction and fastening.

High-manganese steel information Carbide material guidance

Open the shared component catalogue →

Replaceable Segments and Retention Parts

Quick-Connect Segments & Retention Parts

Quick-connect segments and bolt-on primary teeth are key maintenance features. Manufacturing feasibility is established after segment photos, holes, thread/locking details, roll position and drawings are supplied.

Material selection: Confirm retention parts, tooth seats and segment support interfaces against loads, fatigue, heat treatment and inspection requirements. Appearance alone is insufficient for replacement.

Drive alloy steel information Special-alloy material guidance

Open the shared component catalogue →

Side, End and Transfer Liners

Side, End & Transfer Liners

Identify chamber side guards, end protection, feed/discharge and transfer liners. Check flow direction, drop height, thickness, hole spacing, segmentation, fastening and maintenance space.

Material selection: Select liners by zone against impact, abrasion, blockage and wet-material adhesion. The public page does not assign one fixed material solution to a model.

Wear-plate material guidance Composite wear-resistant material information

View the common part page →

قطع الغيار

Roll shafts, bearings, seals and geared-drive spares

The current page emphasizes robust drive trains, shaft and bearing assemblies and multiple drive arrangements. Confirm transmission parts together with series, model, shaft ends, bearings, seals, gearbox and mating relationships.

Roll Shafts and Roll Assemblies

Roll Shaft & Roll Assembly

Confirm roll centres, length, segment layout, shaft ends and shoulders, fits, rotation, roll mass and project drawings. Rolls are commonly matched with segments, bearings and drives.

Material selection: Confirm shaft materials, heat treatment, dimensional accuracy, nondestructive examination and dynamic balance against drawings and loads.

Drive alloy steel information

View the common spare-parts catalogue →

Bearings, Housings and الموانع

Bearings, Housings & الموانع

Check bearing designation, clearance, housing, end cover, seals, lubrication, temperature monitoring and position. Dust, wet material, impact and maintenance conditions affect bearing and seal arrangements.

Material selection: Confirm support, bushing and seal materials separately against loads, medium, temperature, lubrication and inspection standards.

Bushings and plain-bearing material information الموانع and engineering plastics information

View the common part page →

Gearboxes and Drive Gear Sets

علبة التروس & Drive Gear Set

Check gearbox model, ratio, shaft ends, coupling, brake, backstop, lubrication and motor interface. Different drive arrangements cannot be substituted solely by appearance or series name.

Material selection: Gear, shaft, coupling and connector materials, heat treatment, accuracy and inspection requirements follow drawings and actual loads.

Drive alloy steel information

View the common spare-parts catalogue →

Frames, End Plates and Structural Connections

Frame, End Plate & Structural Connections

Identify frames, end plates, inspection doors, support bases, connection plates, pins and field modifications. Provide structural number, general arrangement, welding and inspection requirements, mating interfaces and old-part photos.

Material selection: Confirm structural steel, wear plate and pin materials separately against loads, wear, welding and inspection requirements.

Wear-plate material guidance Special-alloy material guidance

View the common spare-parts catalogue →

Drawing and Part Numbers

Series, project model and OEM drawing checks

Series dimensions and project references are published here, but unverified segment, bearing or gear numbers are not universal ordering codes. Submitted OEM drawings, third-party numbers or used-part records can be mapped to the complete installation.

Submit a TAKRAF OEM drawing number or drawing Check 06–18 Series, TCS-X / TCS project model, roll position, drawing revision and part scope Submit Third-Party References or Used-Part Photographs Locate teeth, segments, retainers, liners, roll shafts, bearings, seals or gearboxes Submit Material and Wear Records Select materials and manufacture using feed size, strength, abrasiveness, wet material, target size and observed failures

Application rule: Establish number applicability only when series, full model, project or serial number, roll/segment configuration, position, drawing revision and physical interfaces agree. 06–18 Series dimension ranges do not replace part drawings.

What is needed for a TAKRAF X-TREME Class Sizer spare-parts enquiry?

Provide 06–18 Series or full TCS / TCS-X model, project or serial number, roll and segment configuration, position, OEM drawing number or drawing, used-part photos, key dimensions, material and conditions.

Can segments or bearings for 06, 08, 12, 14 and 18 Series be replaced using roll centre distance alone?

No. Roll centres only help identify the series. Tooth profile, roll length, fastening, shaft ends, bearings, drives, drawing revisions and modifications may differ and require individual checks.

Why are fixed OEM segment or bearing numbers not listed?

Public manufacturer records do not provide a complete ordering-code table. To avoid treating different projects or configurations as interchangeable, numbers are mapped only after model, project, position and drawings are matched.

TAKRAF كسارات التحجيم المعدنية من فئة X-TREME

Use standard 06–18 Series to identify segments, bearings and drive spares

Standard series, key dimensions and throughput ranges

Identify teeth, replaceable segments and chamber liners

Crushing Teeth and Tooth Segments

Replaceable Segments and Retention Parts

Side, End and Transfer Liners

Roll shafts, bearings, seals and geared-drive spares

Roll Shafts and Roll Assemblies

Bearings, Housings and الموانع

Gearboxes and Drive Gear Sets

Frames, End Plates and Structural Connections

Series, project model and OEM drawing checks

What is needed for a TAKRAF X-TREME Class Sizer spare-parts enquiry?

Can segments or bearings for 06, 08, 12, 14 and 18 Series be replaced using roll centre distance alone?

Why are fixed OEM segment or bearing numbers not listed?

Submit TAKRAF X-TREME Sizer model, drawings or used-part records

من التقييم الفني إلى تسليم المنتج بالكامل

مراجعة الرسومات والهندسة

تحديد المادة والمعالجة الحرارية

ضبط الجودة

تسليم المنتج النهائي