TAKRAF TRC 25.34 / 25.37 الكسارة الأسطوانية المزدوجة قطع الغيار| ANRANST

TAKRAF current product gallery: site assembly reference for toothed rolls, frame and drive areas.

TAKRAF current product gallery: rolls and tooth segments during manufacture in Lauchhammer.

TAKRAF current product gallery: reference for fixed-roll ends, flywheel and drive interfaces.

OEM المعدات Reference

Identify rolls, tooth segments and drives for spare-part supply

TAKRAF double roll crushers serve oil sands and other high-throughput applications. The published design has a fixed roll and a hydraulically supported movable roll rotating inward, with roll gap controlling product size. Enquiries must include full model, project or serial number, fixed/movable position, segment layout, drive and hydraulic-release configuration, mounting interfaces and drawing revision.

10,000–19,000 t/h Current manufacturer-published capacity

2.5 m Current manufacturer-published roll diameter

1,500 kW Published drive rating

12 tooth segments Published circumferential segment count

Standard Models and Key Dimensions

Published models, project identifiers and key ranges

Only ranges and model references supported by current TAKRAF product pages, project pages and historical technical articles are included. TRC machines are project-engineered for high throughput. Similar names, equal roll diameters or oil-sands service do not establish interchangeability of segments, shafts, bearings, fluid couplings or drawing numbers.

Published model / range	Published dimensions or capacity	Project and identification details	Product status
TAKRAF الكسارة الأسطوانية المزدوجة range	Capacity 10,000–19,000 t/h; roll diameter 2.5 m; oil sands and other high-throughput applications	Confirm fixed/hydraulic movable rolls, segments, roll gap, drive and safety release against the specific installation	Current product range
TRC 25.34	Existing primary-station retrofit model named in a historical manufacturer article; confirm dimensions from project drawings	2014 oil-sands primary-station retrofit reference; check project number, fixed/movable roll, segments, drive and fluid-coupling configuration	Historical installation / retrofit identification
TRC 25.37	Historical manufacturer article reports sustained 17,000 mtph and contracted 14,000 mtph	2016 reference to two new primary stations; article cites 400 mm × 400 mm maximum product size. Parts still require drawing checks	Historical installation / project identification
Shell MRM / JPM Canada project	Maximum feed 2,500 mm; design 12,000 t/h, maximum 14,000 t/h; hard rock up to 200 MPa	Four existing crushing stations commissioned in 2014. Records identify oil-sands installations and do not establish component interchangeability for other projects	Manufacturer-published project

Submit full model, project or serial number, fixed/movable roll position, segment layout, drive and hydraulic configuration, OEM drawing number or general arrangement, used-part photos and key interface dimensions. Public capacity and project data do not replace spare-part drawings.

قطع الغيار المستهلكة

Identify teeth, segments, roll interfaces and feed protection

The current manufacturer page describes 12 circumferential segments, replaceable teeth or segments and large access doors. Check wear parts by fixed/movable roll, tooth profile and position, material strength, abrasiveness, wet stickiness, impact, fastening and maintenance access. Candidate materials are not universal OEM specifications for all TRC projects.

Crushing Teeth and Replaceable Segments

Crushing Teeth & Replaceable Segments

Provide gripping, crushing and size control on fixed and movable rolls. Check tooth profile and pitch, segment count and positions, fastening holes, locking, wear faces, rotation, feed size, strength and abrasiveness.

Material selection: The manufacturer's public page does not specify a fixed tooth-material grade. Select materials against impact, abrasion, segment construction, connections, weldability and inspection requirements.

High-manganese steel information Carbide material guidance

Open the shared component catalogue →

Segment Retention, Tooth Seats and Roll-Shell Interfaces

Segment Retention, Tooth Seats & Roll-Shell Interface

Identify load-bearing, locking and removal interfaces between segments and roll shell. Supply tooth-seat, fastener, hole, thread/pin, removal-direction, roll-position and drawing-revision details; appearance alone is insufficient for replacement.

Material selection: Confirm retention parts, tooth seats and load-bearing interfaces against fatigue, impact, heat treatment, dimensional accuracy and nondestructive examination requirements.

Drive alloy steel information Special-alloy material guidance

View the common spare-parts catalogue →

Feed Chute, Side Protection and Discharge Wear Liners

Feed Chute, Side Protection & Discharge Wear Liners

Identify liners and guards at the feeder–crusher interface, roll sides, discharge opening and chutes. Check flow direction, drop height, thickness, hole spacing, segmentation, fastening, blockage and maintenance space.

Material selection: Confirm liners and guards by zone against impact, abrasion, wet-material adhesion, temperature and installation space. Project drawings govern materials and drawing numbers.

Wear-plate material guidance Composite wear-resistant material information

View the common part page →

قطع الغيار

Roll shafts, hydraulic release, flywheels and drive spares

Published design references include fixed and hydraulically supported movable rolls, safety couplings, high-inertia drives and a 21 t flywheel. Transmission and load-bearing parts require matched-assembly details, retrofit records, model, shaft ends, interfaces and drawings.

Fixed / Movable Roll and Shaft Assemblies

Fixed / Movable Roll & Shaft Assembly

Confirm fixed/movable position, roll diameter and length, segment layout, shaft ends and shoulders, fits, rotation, mass and project drawings. Rolls are commonly matched with segments, bearings, drives and hydraulic-release structures.

Material selection: Shaft materials, heat treatment, machining accuracy, nondestructive examination and dynamic balance follow drawings, loads and the actual installation.

Drive alloy steel information

View the common spare-parts catalogue →

Hydraulic Release, Safety Couplings and Protection Systems

Hydraulic Release, Safety Coupling & Protection System

The current manufacturer page describes temporary movable-roll release when uncrushable material enters, with safety couplings responding to impact loads. Check cylinders, accumulators, piping, sensors, couplings, protection logic and mounting interfaces.

Material selection: Confirm hydraulic parts, seals, connectors and load-bearing structures separately against pressure, impact, fluid, temperature, fatigue and inspection standards.

الموانع and engineering plastics information Drive alloy steel information

View the common spare-parts catalogue →

Flywheels, Drive Gearboxes and Fluid-Coupling Interfaces

Flywheel, Drive علبة التروس & Fluid-Coupling Interface

The current page publishes a 21 t flywheel and 1,500 kW drive; historical TRC 25.34 / 25.37 articles also discuss fluid couplings in oil-sands projects. Check gearbox model, ratio, shaft ends, flywheel, coupling, brake and lubrication against the installed machine.

Material selection: Gear, shaft, coupling and connector materials, heat treatment, accuracy and inspection requirements must follow drawings and actual loads.

Drive alloy steel information

View the common spare-parts catalogue →

Bearings, Housings, End Covers and الموانع

Bearings, Housings, End Covers & الموانع

Check bearing designation, clearance, housing, end cover, seals, lubrication, temperature monitoring and fixed/movable roll position. Oil sands, dust, wet feed and impact loads affect bearing and sealing arrangements.

Material selection: Confirm load-bearing, bushing and seal materials separately against loads, fluid, temperature, lubrication and inspection standards.

Bushing and sliding-material guidance الموانع and engineering plastics information

View the common part page →

Special Tooling

Segment changeout and handling tooling — check the specific crushing-station configuration

TAKRAF's current page states that 12 smaller segments are easier to replace when dedicated maintenance tools are included with the station. Official images locate segment retrieval to the maintenance platform, but do not publish complete tooling numbers, loads, dimensions or supply scope for every machine.

Segment Changeout, Lifting and Maintenance-Platform Work Area

Tooth-Segment Changeout & Handling Tooling Position

Check segment removal, lifting, transfer, platform, access doors and safe clearances. Submit tooling photos, working loads, lifting points, segment mass, maintenance route, site platform and OEM drawings. Available tooling or retrofit options are defined only after matching these records.

Material selection: Confirm tooling structure, lifting points, pins, connectors and safety factors against actual loads, handling routes, regulations and project acceptance requirements.

Drive alloy steel information Special-alloy material guidance

Submit tooling and site records →

Drawing and Part Numbers

TRC model, project drawing and old part-number checks

This page publishes TRC 25.34, TRC 25.37 and Canadian project references, without presenting unverified segment, gear, bearing or hydraulic numbers as universal ordering codes. OEM drawings, third-party numbers or used-part records can be mapped to the complete installation after submission.

Submit a TAKRAF OEM drawing number or drawing Check TRC model, project number, fixed/movable position, segments and drive/hydraulic drawing revisions Submit Third-Party References or Used-Part Photographs Locate teeth, segments, retainers, rolls, flywheels, hydraulic parts, bearings, seals or gearboxes Submit feed and wear records Select material and manufacture using feed size, strength, abrasiveness, wet stickiness, target product size, impact and observed failures

Application rule: Establish part-number applicability only when full model, project or serial number, fixed/movable roll, segment and drive configuration, position, drawing revision and physical interfaces agree. Current capacity, roll diameter and historical project records cannot replace part drawings.

What is needed for a TAKRAF double roll crusher spare-parts enquiry?

Provide full TRC or equipment model, project or serial number, fixed/movable position, segment layout, drive and hydraulics, OEM drawing number or drawing, used-part photos, key interface dimensions, material and conditions.

Can TRC 25.34, TRC 25.37 or machines with equal 2.5 m rolls share segments and drive parts?

Not without checking. Tooth profile, segment fastening, roll length, shaft ends, drive, hydraulic release, retrofits and drawing revisions may differ. Confirm installation records and actual interfaces.

Why are fixed OEM segment, bearing or tooling drawing numbers not listed?

Public manufacturer records do not provide a complete ordering-code table or tooling list for each machine. To avoid treating different projects or configurations as interchangeable, numbers and tooling scope are established only after model, project, position and drawings are matched.

TAKRAF الكسارات ذات الأسطوانتين

Identify rolls, tooth segments and drives for spare-part supply

Published models, project identifiers and key ranges

Identify teeth, segments, roll interfaces and feed protection

Crushing Teeth and Replaceable Segments

Segment Retention, Tooth Seats and Roll-Shell Interfaces

Feed Chute, Side Protection and Discharge Wear Liners

Roll shafts, hydraulic release, flywheels and drive spares

Fixed / Movable Roll and Shaft Assemblies

Hydraulic Release, Safety Couplings and Protection Systems

Flywheels, Drive Gearboxes and Fluid-Coupling Interfaces

Bearings, Housings, End Covers and الموانع

Segment changeout and handling tooling — check the specific crushing-station configuration

Segment Changeout, Lifting and Maintenance-Platform Work Area

TRC model, project drawing and old part-number checks

What is needed for a TAKRAF double roll crusher spare-parts enquiry?

Can TRC 25.34, TRC 25.37 or machines with equal 2.5 m rolls share segments and drive parts?

Why are fixed OEM segment, bearing or tooling drawing numbers not listed?

Submit TAKRAF TRC model, drawings or used-part records

من التقييم الفني إلى تسليم المنتج بالكامل

مراجعة الرسومات والهندسة

تحديد المادة والمعالجة الحرارية

ضبط الجودة

تسليم المنتج النهائي