2026 · 6 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to | |
|---|---|---|---|---|
| 1 | Breaker plate | Breaker plate on the left side of the housing cutaway | EnduraHog Grinder AB | |
| 2 | Screen grate | Curved screen grate beneath the rotor | EnduraHog Grinder AB | |
| 3 | Housing liner | Rear housing liner in the inlet area | EnduraHog Grinder AB | |
| 4 |  | Rotor assembly | Series-specific rotor in the lower component image | EnduraHog Grinder AB |
| 4 | Rotor assembly | Rotor visible inside the MME access opening | MME | |
| 5 | Hammer | Working hammer at the outer rotor perimeter | EnduraHog Grinder AB | |
| 6 | Rotor disc | Front end disc of the series-specific rotor | EnduraHog Grinder AB | |
| 7 | Rotor shaft | Rotor shaft projecting at the lower left | EnduraHog Grinder AB | |
| 8 | Housing | Blue lower housing of the MME | MME |
| Component |
|---|
| Hammer Axle / Hammer Pin |
| Hammer-pin retainer |
Models with the same components are grouped together; select a group to open its component table.
Models: 30ABE, 34ABE, 45ABE, 56ABE, 59ABE, MME
| No. | Component | Location |
|---|---|---|
| 1 | Impact Plate / Breaker Plate | |
| 2 | Grate Bar | |
| 3 | Side Housing Liner | |
| 5 | Hammer / Swing Hammer | |
| 6 | Model-specific component | |
| 7 | Rotor shaft | |
| Hammer Axle / Hammer Pin | ||
| Hammer pin retainer | Hammer pin end |
The EnduraHog Grinder AB / Mini-Mill Hammer Grinder covers 6 models: 30ABE, 34ABE, 45ABE, 56ABE, 59ABE, MME. Former and renamed designations are listed in the models table on this page.
The EnduraHog Grinder AB / Mini-Mill Hammer Grinder is also documented under these designations: 30ABE, Mini-Mill 30ABE, EZ Access, 34ABE, Mini-Mill 34ABE, 45ABE, 56ABE, 59ABE, MME, Mini-Mill E, Model E.
The EnduraHog Grinder AB / Mini-Mill Hammer Grinder is listed under the Jeffrey Rader brand. Period: 2026. Status: Historical model.
8 components are recorded, including: Hammer / Swing Hammer, Hammer Axle / Hammer Pin, Rotor shaft, Impact Plate / Breaker Plate, Grate Bar, Side Housing Liner, Hammer pin retainer and more. The full list with locations is in the components table on this page.
Model-specific components with their own page: Hammer pin retainer (1 in total).
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry