ANRANST ANRANSTANRAN S&T · Luoyang
ZH EN RU
Request a Quote

Vertical Mill

Core grinding equipment. Roller tyres and table liners face particle-bed compression and abrasion. High-chromium cast iron and hardfaced composites are common material options.

Vertical Mill

Equipment Section View

Vertical Mill cutaway part location diagram
Vertical Mill cutaway part location diagram

Vertical roller mills use several rollers to compress and shear a material bed on a horizontally rotating grinding table. Hot gas enters through the nozzle ring around the table and carries fine particles to the dynamic classifier. Coarse particles return to the table, while tramp material and difficult-to-grind coarse particles leave through the reject system. Principal wear parts are located in the rollers, table, nozzle ring, classifier and dust-laden gas passages.

Equipment Parts

Part Identification and Technical Details

Explore part names, images, material options and technical requirements. Select a card to open the corresponding replacement part page.

Major Components and Assemblies

Major Components and Assemblies

Individual and Maintenance Parts

Individual and Maintenance Parts

Grinding Roller / Roller Tyre Assembly
01

Grinding Roller / Roller Tyre Assembly

Grinding Roller / Roller Tyre

Material Options
High-chromium white iron, Ni-Hard 4 or a steel-backed multilayer hardfacing composite
Technical Requirements
Cast wear layers commonly target approximately 58—65 HRC. For steel-backed composites, consider thermal shock resistance, resistance to brittle fracture and repairability.
Grinding Table / Table Liner Assembly
02

Grinding Table / Table Liner Assembly

Grinding Table / Table Liner

Material Options
High-chromium white iron, Ni-Hard 4 or a steel-backed hardfacing composite
Technical Requirements
Working layer: commonly approximately 55—65 HRC. Control radial wear uniformity and joints between segments.
Grinding Roller Sleeve
03

Grinding Roller Sleeve

Roller Liner / Roller Sleeve

Material Options
Replaceable high-chromium cast iron roller tyres or hardfaced composite tyres
Technical Requirements
Balance abrasion resistance, spalling resistance and secure fit on the roller core.
Segmented Grinding Table Liner
04

Segmented Grinding Table Liner

Table Segments / Grinding Plates

Material Options
High-chromium white iron, Ni-Hard 4 or steel-backed hardfaced composite plate
Technical Requirements
Control segment hardness, thickness and weight variation to prevent table vibration and local high spots.
Nozzle Ring / Louver Ring
05

Nozzle Ring / Louver Ring

Nozzle Ring / Louver Ring

Material Options
Heat- and wear-resistant alloy steel, wear-resistant steel or hardfaced composites
Technical Requirements
Requires erosion and thermal cycling resistance; the working layer is commonly approximately 45—60 HRC, depending on specification.
Air Classifier Blade
06

Air Classifier Blade

Classifier Blade / Vane

Material Options
NM400/NM450, hardfaced wear plate or ceramic composites
Technical Requirements
Wear-resistant steel: approximately 400—500 HBW; hardfacing: commonly approximately 55—62 HRC. Control blade weight balance.
Dam Ring
07

Dam Ring

Dam Ring / Retention Ring

Material Options
Wear-resistant steel, low-alloy cast steel or hardfaced composites
Technical Requirements
Requires erosion and deformation resistance. Height and clearance directly affect material bed thickness.
Mill Shell Liner
08

Mill Shell Liner

Mill Body Liner / Housing Liner

Material Options
NM400—NM500, bimetallic composite plate or wear-resistant ceramics
Technical Requirements
Steel plate: approximately 400—540 HBW, depending on grade. Protect areas exposed to high-velocity, dust-laden gas erosion.
Feed Chute Liner
09

Feed Chute Liner

Feed Chute Liner

Material Options
NM450/NM500, bimetallic or ceramic-rubber composites
Technical Requirements
Account for falling-material impact, erosion and buildup, using replaceable sections.
Reject Chute Liner
10

Reject Chute Liner

Reject Chute Liner

Material Options
NM400—NM500 or bimetallic composite plate
Technical Requirements
Resists impacts from tramp iron, coarse particles and hot material, with additional protection at changes in flow direction.
Grinding Roller Bearing / Seal
11

Grinding Roller Bearing / Seal

Roller Bearing / Bearing Seal

Material Options
GCr15/100Cr6 bearing steel; NBR, HNBR or FKM seals
Technical Requirements
Raceway: commonly approximately 60—64 HRC. Seals must withstand dust, lubricating oil or grease and operating temperature.
Hydraulic Cylinder Seal
12

Hydraulic Cylinder Seal

Hydraulic Cylinder Seal

Material Options
PU primary seals with NBR/FKM secondary seals and backup rings
Technical Requirements
PU: commonly approximately 90—95 Shore A. Requires pressure and wear resistance, extrusion resistance and low leakage.

Materials for similarly named parts may differ by OEM, machine model and operating conditions. Confirm the machine model, OEM drawing number and measured dimensions before ordering or manufacture.

Materials for similarly named parts may differ by OEM, machine model and operating conditions. Confirm the machine model, OEM drawing number and measured dimensions before ordering or manufacture.

Equipment Manufacturers and Series

Claudius Peters LOESCHE thyssenkrupp Mining Technologies (legacy)

Request a Vertical Mill Wear Parts Proposal

Provide the machine model, operating conditions and target service life so our engineers can recommend materials and prepare a quotation.

Send Operating Details for a Quote

Or contact us directly: +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with coordinated consulting, supplier sourcing, quality control and finished-part delivery for custom parts, wear parts and industrial spares from China, with scope to support other custom industrial parts.

01

Technical Advice

Equipment and part identification, drawing review, material selection and manufacturing feasibility assessment.

02

Supplier Introductions

Match requirements with suitable manufacturers in China and coordinate the exchange of technical information.

03

Quality Control

Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.

04

Finished-Part Delivery

Coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts.

Provide the existing model, drawings, drawing or part numbers, materials or operating conditions so we can identify the appropriate technical review and supply route.

Submit an Enquiry