Start with the brand, equipment series and installed machine, then explore wear parts, drive and structural spares, materials and processes, drawing review, quality control and finished-part delivery.
This page covers equipment series and models, part locations, materials and processes, drawing review and inquiry options. Before manufacture or quotation, confirm drawing, dimensions and tooling suitability against the complete model and drawings.
The model table assists with machine identification. Manufacture and quotation require the nameplate, complete model, serial number, drawing, general arrangement and drawing revision.
| Series / Model | Equipment Range and Identification | Equipment History and Identification |
|---|---|---|
| Fuller-Traylor gyratory crushers | NT; TS; TSUV | Historical Installed Equipment Series |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Bar-type spider | Spider at top of crusher | FLS TSUV (configuration in this brochure) |
| 2 | Spiral bevel gearing | Drive gearing beside lower main shaft | FLS TSUV (configuration in this brochure) |
| 3 | Countershaft assembly | Countershaft at lower right | FLS TSUV (configuration in this brochure) |
| 4 | Eccentric and hydraulic piston assembly | Eccentric and hydraulic support around lower shaft | FLS TSUV (configuration in this brochure) |
| 5 | Integral main-shaft | Integral main shaft at centre | FLS TSUV (configuration in this brochure) |
| 6 | Integral main-shaft lifting eye | Integral lifting eye at top of main shaft | FLS TSUV (configuration in this brochure) |
| 7 | Spider grease lubrication line | Grease connection beside upper spider bushing | FLS TSUV (configuration in this brochure) |
| 8 | Spider bushing | Guide bushing around upper main shaft | FLS TSUV (configuration in this brochure) |
| 9 | Top shell wear plate | Wear plate along top shell rim | FLS TSUV (configuration in this brochure) |
| 10 | Dust seal pressurised chamber | Pressurised seal chamber around lower main shaft | FLS TSUV (configuration in this brochure) |
| 11 | Bottom shell view port | View port on lower right shell | FLS TSUV (configuration in this brochure) |
These general Gyratory Crusher part categories help identify the part you need. Confirm suitability against the specific Fuller-Traylor model and drawings.
Mainshaft Sleeve
A general wear part category for Gyratory Crusher equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →Mantle
A general wear part category for Gyratory Crusher. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
Send Drawings for Review →
Eccentric Bushing
A general wear part category for Gyratory Crusher equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →Bottom Shell Bushing
A general wear part category for Gyratory Crusher. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
Send Drawings for Review →
Eccentric Wear Plate
A general wear part category for Gyratory Crusher equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →
Mainshaft Step Plate
A general wear part category for Gyratory Crusher equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →Identify gears, shafts, sleeves, bearings, seals, hydraulic parts, supports and connectors for drawing review. Listed OEM drawing or part references relate to identified parts and require confirmation against your machine.
Mainshaft Sleeve
A general structural or drive part category for Gyratory Crusher equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →
Dust Seal
A general structural or drive part category for Gyratory Crusher equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →Eccentric Bushing
A general structural or drive part category for Gyratory Crusher equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →Bottom Shell Bushing
A general structural or drive part category for Gyratory Crusher. Confirm interfaces, accuracy, material and applicable model against the equipment drawings.
Send Drawings for Review →
Gear
A general structural or drive part category for Gyratory Crusher equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →Eccentric Wear Plate
A general structural or drive part category for Gyratory Crusher equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
Send Drawings for Review →Provide the complete model, serial number, drawing revision, installation position, photographs of the current part, material and operating conditions.
No. General images help identify the part category. Manufacture requires agreed drawings, dimensions, interfaces, materials and acceptance criteria.
Start with the nameplate, general arrangement drawing, installation position, used-part photographs and key dimensions. We can then assess the feasibility of dimensional inspection, material evaluation and manufacture to drawing.
Provide the complete model, serial number, nameplate, installation position, photographs of the current part, drawings, material and operating conditions. We use these to identify the part, assess materials, organize production at certified foundries, coordinate quality control and arrange finished-part delivery.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the equipment brand, complete model and serial number, part name, part number or drawing number, drawing revision, quantity, material requirements and duty. If identifiers are unavailable, send photographs and key dimensions.
Submit an Enquiry