Truck-mounted water well and exploration drilling rig · 2 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Components |
|---|---|---|
| Driltech D25KW water well/exploration drilling rig | D25KW (water well series); Driltech D25KW | 18 |
| Driltech T truck-mounted drill series (T25KW / T40KW / T40KX identified) | T25KW; T40KW; T40KX; TM40KW; Driltech T25K2W; T25 KW; Driltech T25K4W | 9 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Mast | Vertical mast at the rear of the truck | T25K2W |
| 2 | Deck power group | Deck power equipment behind the truck cab | T25K2W |
| 3 | Leveling jack | Support jack immediately behind the truck cab | T25K2W |
| 4 | Truck chassis | Wheels and chassis below the drilling deck | T25K2W |
| Component |
|---|
| Vertical air storage tank |
| Liquid level sight glass and safety relief valve |
| Minimum pressure valve and oil and gas separation filter element |
| Separate pressure difference indication and oil return system |
| Oil temperature thermostat and oil cooling bypass valve |
| Oil cooler and oil stop valve |
| Temperature/pressure safety switch |
| Two-stage air compression host, discharge check valve and high temperature hose |
| Deck diesel engine and air compressor |
| Rod holder and drill pipe |
| Rotary head and adjustable drill floor |
| Hydraulic rotating boom and auxiliary winch |
| Hydraulic breakout wrench |
| Water injection/foam pump and air lubricator |
| Operating platform, remote control and fine-tuning control |
| Work light with bushing/slip |
| 2001 stock rod holder, leveling legs and rod library |
| 2001 Stock Deck Power and Air Compressor |
| Optional Twin Disc friction plate/adjustment ring/lock |
| Mud pump closed loop piston pump and motor |
| Vertical operation electric control panel |
| switches, indicators, instruments and junction boxes |
| GHH compressor and CAT3406 deck engine (this unit) |
| Four-piston water injection pump (this set) |
| Feed chain (replacement statement for this unit) |
| Comes with drill pipe and basic tooling not listed below |
| BECO adapted drill pipe (127/140/152.4/159/165.1 description file) |
Models with the same components are grouped together; select a group to open its component table.
| Component | Location |
|---|---|
| Vertical air storage tank | Water well high pressure air system |
| Liquid level sight glass and safety relief valve | Vertical air storage tank |
| Minimum pressure valve and oil and gas separation filter element | High pressure air storage tank/separation area |
| Separate pressure difference indication and oil return system | Compressor separation circuit |
| Oil temperature thermostat and oil cooling bypass valve | Compressor cooling oil circuit |
| Oil cooler and oil stop valve | Compressor oil circuit |
| Temperature/pressure safety switch | High voltage system monitoring |
| Two-stage air compression host, discharge check valve and high temperature hose | High pressure air system |
| Deck diesel engine and air compressor | This CatC15/Sullair; not standard equipment for other years |
| Rod holder and drill pipe | This machine comes with rod holder/drill pipe, not an independent model. |
| Rotary head and adjustable drill floor | The rotary drilling/table |
| Hydraulic rotating boom and auxiliary winch | Mast installation auxiliary for this platform |
| Hydraulic lever wrench | The position of the disassembly rod of this machine |
| Water injection/foam pump and air lubricator | The injection/tool lubrication circuit |
| Operating platform, remote control and fine-tuning control | Operation assistance of this station |
| Work light with bushing/slip | This unit comes with lights and drill floor |
| 2001 stock rod holder, leveling legs and rod library | The table is equipped with poles/supports |
| 2001 Stock Deck Power and Air Compressor | This Cat3406E/Sullair |
| Component | Location |
|---|---|
| Optional Twin Disc friction plate/adjustment ring/lock | T25KW/T40KW/T40KX optional mud pump clutch |
| Mud pump closed loop piston pump and motor | Main T40KW water well optional circuit |
| Vertical operation electric control panel | T25KW vehicle-mounted water well control position |
| switches, indicators, instruments and junction boxes | T25KW specific electrical configuration; CCC/Ford/Sterling chassis in separate volume |
| GHH compressor and CAT3406 deck crane (this unit) | Deck power/air system |
| 4-piston water injection pump (this set) | Water injection system |
| Feed chain (replacement statement for this unit) | Mast feed |
| Comes with drill pipe and basic tooling not listed below | This unit comes with stock |
| BECO adapted drill pipe (127/140/152.4/159/165.1 description file) | Drill string; only T25KW; L9144mm, 127/140 uses 3½BECO, the rest 4½BECO; 159 corresponds to ØA158.8mm |
The Truck-mounted water-well and exploration Drill rig covers 2 models: Driltech D25KW water well/exploration drilling rig, Driltech T truck-mounted drill series. Former and renamed designations are listed in the models table on this page.
The Truck-mounted water-well and exploration Drill rig is also documented under these designations: D25KW, Driltech D25KW, Driltech T truck-mounted drill series, T25KW, T40KW, T40KX, TM40KW, Driltech T25K2W, T25 KW, Driltech T25K4W.
The Truck-mounted water-well and exploration Drill rig is listed under the DrilTech Mission brand as: Truck-mounted water well and exploration drilling rig. Status: Historical model.
27 components are recorded, including: Vertical air storage tank, Liquid level sight glass and safety relief valve, Minimum pressure valve and oil and gas separation filter element, Separate pressure difference indication and oil return system, Oil temperature thermostat and oil cooling bypass valve, Oil cooler and oil stop valve, Temperature/pressure safety switch, Two-stage air compression host, discharge check valve and high temperature hose and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry