Cone crusher · 3 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| AMS Hydrocone 1000 Series | Allis Mineral Systems H-3000; Allis Mineral Systems-Svedala H-6000 | 12 | |
| AMS/Svedala Arbrå H-200 Hydrocone cone crusher | AMS H-200 Hydrocone; H200 | 1987 2000 EPO | 28 |
| AMS imperial-size Hydrocone cone crushers | Allis-Chalmers Hydrocone 84 | 7 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Mantle | Outside moving cone | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| 2 | Concave | Fixed crushing surface in top shell | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| 3 | Spider bushing | Around shaft in spider center | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| 4 | Mainshaft sleeve | Shaft below spider | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| 5 | Eccentric bushing | Between eccentric and shaft | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| 6 | Pinion | Inner pinionshaft drive end | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| 7 | Hydroset piston | Inside cylinder below mainshaft | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| 8 | Dust seal ring | Dust interface under moving cone | AMS inch-size Hydrocone design family only; H-200 and 1000 series excluded |
| Component |
|---|
| Mantle / Head Liner — Mantle liner listed in the ancillary-product table |
| Bowl Liner / Concave — Concave liner listed in the ancillary-product table |
| Crush-Bac resin component (maintenance consumables) |
| Crush-Bac curing agent components (maintenance consumables) |
| Backing Construction Mixing Paddle Tool Category |
| Release agent for backing construction (matching consumables) |
| Backing construction leak-proofing material (matching consumables) |
| Savona H3000 medium shredded lining |
| Savona H3000 fine shredded lining |
| Savona H3000 motor |
| Lubricating oil tank sold with Savona H3000 |
| Fan sold with Savona H3000 |
| Monitor included with Savona H3000 |
| Savona H6000 head configuration |
| Motor sold with Savona H6000 |
| Starter sold with Savona H6000 |
| Savona H6000 missing eccentric component |
| Savona H6000 missing ring gear |
| Savona H6000 missing pinion assembly |
| H200 refurbished movable frame (2016 example) |
| H200 refurbished and newly installed support (2016 example) |
| H200 refurbished Hydroset system (2016 example) |
| H200 refurbished cooling fan (2016 example) |
| H200 refurbished skid (2016 example) |
| H200 refurbished guard (2016 example) |
| H200 refurbished handrail (2016 example) |
| H200 refurbished motor (2016 example) |
| H200 refurbished pulley (2016 example) |
| H200 refurbished transmission belt (2016 example) |
| H200 lubrication system (second refurbishment example) |
| H200 Skid Frame (Second Refurbishment Example) |
| H200 upper chassis (second refurbished example) |
| H200 shelf bushing (second refurbished example) |
| H200 motor (second refurbishment example) |
| H200 transmission belt (second refurbished example) |
| H200 main shaft thrust seat (second refurbishment example) |
| H200 thrust washer (second refurbishment example) |
| H200 piston wear plate (second refurbishment example) |
| H200 pinion shaft (second refurbished example) |
| H200 bearing category (second refurbishment example) |
Models with the same components are grouped together; select a group to open its component table.
| Component | Location |
|---|---|
| H200 refurbished movable frame (2016 example) | live frame |
| H200 refurbished and newly installed support (2016 example) | new mounts, type not documented |
| H200 refurbished Hydroset system (2016 example) | Renovated hydraulic adjustment system |
| H200 refurbished cooling fan (2016 example) | Added cooling components |
| H200 refurbished skid (2016 example) | Added skid frame |
| H200 refurbished guard (2016 example) | Add new guards |
| H200 refurbished handrail (2016 example) | Add handrails |
| H200 refurbished motor (2016 example) | New motor, no power loaded |
| H200 refurbished pulley (2016 example) | New pulley |
| H200 refurbished transmission belt (2016 example) | new drive belts |
| H200 lubrication system (second refurbishment example) | Refurbishment of Svedala lubrication system |
| H200 Skid Frame (Second Refurbishment Example) | Refurbished Svedala skid-frame |
| H200 upper chassis (second refurbished example) | Modified topshell for spider bushing |
| H200 shelf bushing (second refurbished example) | New bushing conversion, does not cover all original machines |
| H200 motor (second refurbishment example) | Added 75kW motor |
| H200 transmission belt (second refurbished example) | Added drive belts |
| H200 main shaft thrust seat (second refurbishment example) | mainshaft step |
| H200 thrust washer (second refurbishment example) | step washer |
| H200 piston wear plate (second refurbishment example) | piston wear plate |
| H200 pinion shaft (second refurbished example) | pinion shaft |
| H200 bearing category (second refurbishment example) | Pinion shaft related list, specific model not included |
| H200 seal category (second refurbishment example) | seals, specific material type not specified |
| H200 Gasket Category (Second Refurbishment Example) | gaskets, specific material type not specified |
| H200 manganese steel liner (second refurbishment example) | CMS newly added liner, no transfer/fixed cone quantity |
| H200 compression rubber mounting support (second refurbishment example) | rubber compression mountings |
| H200 accumulator (second refurbishment example) | Add accumulator |
| H200 handrail (second renovation example) | new hand rails |
| H200 guard (second refurbishment example) | new guarding |
| Component | Location |
|---|---|
| Savona H3000 medium shredded lining | The first Medium liner of the two in stock; the original section does not distinguish the transmission/fixed cone lining |
| Savona H3000 fine shredded lining | Another Fine liner; not the same one equipped with both medium and fine liners |
| Savona H3000 motor | Original Electric Motor150HP, non-capable push motor |
| Lubricating oil tank sold with Savona H3000 | Comes With; does not prove all members of the original OEM oil station |
| Fan sold with Savona H3000 | The purpose/installation position is not specified, and the oil cooler fan is not guessed. |
| Monitor included with Savona H3000 | Originally called Computer Screen, it is not equivalent to the entire automatic control system |
| Savona H6000 head configuration | The original Standard Head and Shorthead Arrangement, the assembly relationship is not clear, the aggregation does not count the two ends that are installed together. |
| Motor sold with Savona H6000 | 300HP, the original text clearly states that it is sold with |
| Starter sold with Savona H6000 | Listed in the same item as the motor, but the model is not specified |
| Savona H6000 missing eccentric component | Less: The seller clearly stated that the missing parts were not used as existing installed components. |
| Savona H6000 missing ring gear | Less: Ring Gear, the exact configuration and interchangeability with other models are not stated |
| Savona H6000 missing pinion assembly | Less: Pinion Gear Assembly; missing parts need to be replaced, incorrectly installed |
| Component | Location | Part / drawing no. |
|---|---|---|
| Mantle / Head Liner — Mantle liner listed in the ancillary-product table | The manufacturer's backing list is mantle; the number of lining plates is not calculated based on the estimated backing quantity. | 07-349-708-001 / 20386 |
| Bowl Liner / Concave — Concave liner listed in the ancillary-product table | Manufacturer backing list concave | FV-17067-D / 07-453-356-001 |
| Crush-Bac resin component (maintenance consumables) | Matching backing kit Part1 | |
| Crush-Bac curing agent components (maintenance consumables) | Matching backing kit Part2 | |
| Backing Construction Mixing Paddle Tool Category | The application instructions recommend drilling rig paddle mixing and do not certify random special tooling. | |
| Release agent for backing construction (matching consumables) | Surface intended to be non-adhesive to casing/threads | |
| Backing construction leak-proofing material (matching consumables) | Seam/bottom seam sealing and diversion |
The Cone crusher covers 3 models: AMS Hydrocone 1000 Series, AMS/Svedala Arbrå H-200 Hydrocone cone crusher, AMS imperial-size Hydrocone cone crushers. Former and renamed designations are listed in the models table on this page.
The Cone crusher is also documented under these designations: AMS Hydrocone 1000 Series, Allis Mineral Systems H-3000, Allis Mineral Systems-Svedala H-6000, AMS/Svedala Arbrå H-200 Hydrocone cone crusher, AMS H-200 Hydrocone, H200, AMS imperial-size Hydrocone cone crushers, Allis-Chalmers Hydrocone 84.
The Cone crusher is listed under the Allis Mineral Systems brand as: Cone crusher. Status: Historical model.
47 components are recorded, including: Savona H3000 medium shredded lining, Savona H3000 fine shredded lining, Savona H3000 motor, Lubricating oil tank sold with Savona H3000, Fan sold with Savona H3000, Monitor included with Savona H3000, Savona H6000 head configuration, Motor sold with Savona H6000 and more. The full list with locations is in the components table on this page.
Mantle / Head Liner: 07-349-708-001 / 20386, Bowl Liner / Concave: FV-17067-D / 07-453-356-001.
Model-specific components with their own page: Crush-Bac resin component (maintenance consumables), Crush-Bac curing agent components (maintenance consumables), Backing Construction Mixing Paddle Tool Category, Release agent for backing construction (matching consumables), Backing construction leak-proofing material (matching consumables) (5 in total).
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry