01
Backup Rotor Tips
Back-up Tip
Located at rotor outlets, they continue protecting the rotor after main-tip wear. Check rotor model, handedness, holes, profile, matching tips and installation sequence.
View the Component Page →Sandvik CV200 Vertical Shaft Impact Crushers
Use current CV215–CV229 models to identify rotor tip systems, feed parts, internal and external wear plates, main shafts, bearings, drives and materials for quotation.
OEM equipment guide
Models, Rotor Wear Systems and Shaft Spares on One Page
Models and key data identify the installation. Wear parts are grouped by rotor feed, discharge passages, internal/external protection and chamber position; shafts and drive parts are listed separately.
6Current Standard Models
40–55 mmMaximum Feed Size
10–600 t/hCapacity Range on the Official Website
55–500 kWMotor Power
Models and key specifications
Current CV215–CV229 Models and Key Specifications
Weight, maximum feed, capacity and motor power come from current Sandvik stationary VSI product pages and support initial installation identification.
| Model | Weight | Maximum Feed | Capacity | Motor Power |
|---|---|---|---|---|
| CV229 | 14,826 kg | 55 mm | 445–600 t/h | 500 kW |
| CV228 | 14,826 kg | 55 mm | 271–444 t/h | 370 kW |
| CV218 | 11,776 kg | 55 mm | 193–270 t/h | 250 kW |
| CV217 | 9,500 kg | 50 mm | 122–192 t/h | 185 kW |
| CV216 | 9,500 kg | 50 mm | 51–121 t/h | 110 kW |
| CV215 | 6,000 kg | 40 mm | 10–50 t/h | 55 kW |
Actual capacity varies with material, feed grading, rotor configuration, speed, Bi-Flow settings, crushing mode and closed-circuit conditions.
Sandvik
Component Location Diagram
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Rotor | Central cylindrical rotating assembly | CV200 |
| 2 | Feed tube | From the top inlet to the rotor | CV200 |
| 3 | Main shaft assembly | Vertical support and drive beneath the rotor | CV200 |
| 4 | Drive motor | Motor module at the base | CV200 |
| 5 | Inspection door | Side opening into the crushing chamber | CV200 |
Wear parts
Rotor Tip Systems, Feed Parts and Chamber Wear Parts
Identify each part by position. Material selection considers high-speed abrasion, centrifugal loads, local impact, fracture risk and rotor dynamic balance together.
02
Tip Cavity Wear Plates
Tip Cavity Wear Plate
Protect the rotor cavity near the tips. Check rotor ports, orientation, plate profile, holes, thickness and compatibility with the tip system.
View the Component Page →
03
Trail Wear Plates
Trail Plate
Installed in trailing areas of rotor discharge passages, they face high-speed flow erosion. Check position reference, direction, curvature, holes and overlaps with upper/lower wear plates.
View the Component Page →
04
Feed Eye Ring
Feed Eye Ring
At the central rotor inlet, it guides feed and protects the edge. Check inside/outside diameters, thickness, holes, locating features and feed-tube clearance.
View the Component Page →
05
Feed Tube
Feed Tube
Directs material into the rotor centre. Check diameters, length, flange, installation height, concentricity, flow direction and fit with the feed eye ring.
View the Component Page →
06
Upper Internal Wear Plates
Upper Internal Wear Plate
Protect upper internal rotor flow passages. Check position, direction, holes, curvature, thickness and overlaps with adjacent plates.
View the Component Page →
07
Lower Internal Wear Plates
Lower Internal Wear Plate
Protect lower internal rotor passages. Check position, direction, segment sequence, holes, thickness and relationship with external plates.
View the Component Page →
08
Top External Wear Plates
Top External Wear Plate
Protect exposed top rotor surfaces. Check rotor specification, orientation, holes, thickness, profile and dynamic clearances.
View the Component Page →
09
Bottom External Wear Plates
Bottom External Wear Plate
Protect the rotor's external bottom area. Check top/bottom orientation, direction, holes, thickness, profile, clearances and relationship with base guards.
View the Component Page →
10
Lid Liners
Lid Liner
Protect the chamber lid's inner surface. Check segment references, direction, holes, thickness, overlaps, access openings and rotor-sweep clearances.
View the Component Page →
11
Base Protection Liners
Pedestal Protection Liner
Protect the bearing pedestal and surrounding lower structure. Check installation zone, segmentation, holes, thickness and safe clearance to rotor bottom plates.
View the Component Page →
12
Anvil Ring Assembly
Anvil Ring Assembly
For installations configured for anvil crushing. Check crushing mode, ring dimensions, anvil count, positions, fastening and alignment with rotor discharge trajectories.
View the Component Page →CV200 VSI crushers
Wet-end and wear-part identification
The current stationary-VSI directory lists CV215, CV216, CV217, CV218, CV228 and CV229. Preserve the full CV model. Record rotor and Bi-Flow configuration independently of the model string. source
Nameplate identification
Send legible carrier and crusher nameplates: manufacturer, complete model and suffix, serial number, and year where stated. Identify your parts / send nameplate.
full CV model; rotor identity and dimensions; wear-set photographs; rock-bed chamber; Bi-Flow gate configuration
Spare parts
Rotor, Main Shaft, Bearing, Base and Drive Spares
Verify drive and support parts by full model, rotor specification, speed, direction, fits, tolerances, lubrication and dynamic balance.
01
Rotor Assembly and Body
Rotor Assembly / Rotor Body
The VSI's main high-speed rotating assembly. Check rotor specification, diameter, ports, feed eye, discharge passages, shaft interface, rotation and balance requirements.
View the Component Page →
02
Main Shaft
Main Shaft
Supports and drives the rotor. Check shaft diameters, bearing seats, taper-bush or key connection, ends, rotation, runout, heat treatment and non-destructive testing.
View the Component Page →
03
Rotor Bearings
Rotor Bearing
Carry high-speed rotor loads. Check full bearing designation, clearance, fits, tolerances, speed, lubrication, seals, temperature rise and vibration monitoring.
View the Component Page →
04
Bearing Pedestals and Housings
Bearing Pedestal / Housing
Locate main-shaft bearings and connect them to the frame. Check centre height, mounting and bearing bores, tolerances, oil passages, seal interfaces and datum surfaces.
View the Component Page →
05
Rotor Bearing Seals
Rotor Bearing Seal
Exclude dust from high-speed bearings and retain lubrication. Check shaft diameter, seal design, direction, clearances, lubricant and operating temperature.
View the Component Page →
06
Drive V-Belts
Drive V-belt
Transmit power from the motor to the main shaft. Check belt section, length, count, matched-set tolerances, pulley diameters, centres and tensioning.
View the Component Page →
07
Taper Lock Bushes
Taper-lock / Tapered Sleeve
Provide tapered locking between pulleys or rotating parts and shafts. Check taper, inside/outside diameters, keyways, bolt holes, shaft diameter and mating pulley.
View the Component Page →FAQ
Frequently asked questions
Is the machine model enough to identify CV200 wear parts?
No. Also check rotor specification, ports and crushing mode, position, direction, part drawing, key dimensions, material and matched assemblies.
Can rotor tips, backup tips and cavity wear plates be replaced independently?
First verify rotor design and matched-part relationships. Similar shape does not imply identical position, direction, clearance, weight or balance requirements.
Can I request a quotation without a published model details?
Yes. Send the full model, serial number, rotor and used-part photographs, position, key dimensions or drawings so we can first identify the part technically.