Sealing Elastomers and Engineering Plastics

For seals, wipers and guides in hydraulic cylinders, rotating shafts, bearings, dust protection systems and slurry equipment. Select materials by fluid, pressure, temperature, speed, motion, groove geometry and surface condition.

Fluid and Motion Determine Material Selection

NBR, HNBR, FKM, PU and PTFE cannot be substituted by colour or shape alone

Elastomers provide resilience and contact pressure. Polyurethane offers wear and extrusion resistance in selected dynamic hydraulic seals. PTFE and its composites provide low friction and chemical compatibility, while engineering plastics are often used for guide rings, wear rings and supports. Select the material together with the seal type and complete groove design.

Main Part Applications

Group parts by function, then select materials for the fluid and operating conditions.

01 · HYDRAULIC

Hydraulic Cylinder Seals and Guides

Pièce
Resistance to hydraulic fluids, pressure cycling, extrusion, friction, wear and contamination, with resilience and dimensional stability.
Propriétés requises
Piston seals, rod seals, wipers, buffer seals, static seals, guide rings and wear rings.

Seals and guides form a system. Check grooves, clearances and rod surface damage when replacing a seal.

02 · ROTARY SHAFT

Rotary Shaft and Bearing Seals

Pièce
Low friction, oil and temperature resistance, wear resistance and stable lip contact, with allowance for shaft eccentricity and dust.
Propriétés requises
Pinion shaft seals, bearing seals, elastomeric elements in labyrinth seal assemblies and mechanical seal secondary seals.

Speed, shaft diameter, runout and inadequate lubrication can rapidly change material performance.

03 · DUST & SLURRY

Dust, Slurry and Static Seals

Pièce
Particle exclusion, fluid compatibility, wear resistance and resilience; slurry service also requires assessment of erosion and solids.
Propriétés requises
Gyratory crusher dust seals, O-rings, gaskets, pump packing, mechanical seal secondary parts and protective wipers.

Slurry pump wet-end linings and seals have different functions. A rubber lining compound is not automatically suitable for a shaft seal.

Material Families, Properties and Parts

After selecting a material family, define temperature limits and service life targets for the specific operating conditions.

Material FamilyKey PropertiesTypical PartsSelection Limits
NBR Nitrile RubberA balance of elasticity, sealing and wear resistance in common oil applications.O-rings, static seals, selected shaft seals and conventional hydraulic seals.Oil type, low and high temperatures, ozone and the specific compound; the NBR designation alone does not establish suitability.
HNBR Hydrogenated Nitrile RubberGreater resistance than conventional NBR to selected thermal, mechanical and environmental ageing conditions.Heavy-duty hydraulic seals, dynamic seals and more demanding oil applications.Check fluid compatibility, temperature, pressure cycling and compound certification.
FKM FluoroelastomerStable sealing in selected high-temperature, oil and chemical applications.High-temperature oil seals, static seals and secondary seals for special fluids.Low temperatures, steam and amines may limit suitability; consult the compound compatibility data.
PU PolyurethaneWear, tear and extrusion resistance for selected reciprocating hydraulic seals.Piston and rod seals, wipers, buffer seals and wear rings.Hydrolysis, temperature, fluid compatibility and friction at high speed; seal PU compounds differ from mining liner PU compounds.
PTFE and CompositesLow friction, broad chemical compatibility and low adhesion; fillers can modify load capacity and wear performance.Sliding rings, rotary and reciprocating seals, guide rings, wear rings and mechanical seal secondary parts.Resilience, cold flow, creep, mating surfaces and preload design; often used in combination with an elastomer.
Engineering Plastics / Composite Guide MaterialsSupport, guidance, low friction, seizure resistance and dimensional stability.Guide rings, support rings, wear rings, and insulating or low-friction separators.Bearing pressure and speed, temperature, water absorption, creep, lubrication and clearance.

Control Points from Drawing to Delivery

Small seals can have a major effect on equipment downtime.

Material Identification

Record the material family, compound or grade, batch and certificate; colour is not a reliable material identifier.

Dimensions and Appearance

Check cross-section, bore and outside diameter, lips, flash, nicks, surfaces and deformation caused by packaging.

Grooves and Mating Surfaces

Check groove dimensions, extrusion gaps, shaft or cylinder surfaces, chamfers and assembly orientation.

System Validation

Assess compatibility and perform necessary bench or trial-fit testing for the fluid, pressure, temperature and motion.

Find the Relevant Parts

Use the part pages to check drawing, spare model details, installation positions and applicable models.

Technical References: Trelleborg Sealing Solutions distinguishes NBR, HNBR, FKM, polyurethane and other elastomers, and explains how materials interact with fluids, temperatures and seal designs. The final grade and application limits depend on complete operating conditions, customer drawings and supplier material data.

Send Fluid, Motion and Groove Dimensions

Please provide the equipment model, drawing, seal type, fluid, pressure, temperature, speed, shaft or bore diameter, groove dimensions, current material, failure photographs and quantity.

Send Technical Details and an Inquiry

Send Your Wear Part Requirements

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry