2026-10-03 · 7 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Period | Components |
|---|---|---|
| KREBS slurryMAX-HP 10x8 | 2026-10-03 | 11 |
| KREBS slurryMAX-HP 12x10 | 2026-10-03 | 11 |
| KREBS slurryMAX-HP 14x12 | 2026-10-03 | 11 |
| KREBS slurryMAX-HP 16x14 | 2026-10-03 | 11 |
| KREBS slurryMAX-HP 4x4 | 2026-10-03 | 11 |
| KREBS slurryMAX-HP 6x6 | 2026-10-03 | 11 |
| KREBS slurryMAX-HP 8x6 | 2026-10-03 | 11 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location |
|---|---|---|
| 1 | Impeller | Red wet-end impeller |
| 2 | Wear ring | Front of the impeller eye |
| 3 | Suction liner | Blue lining around the suction inlet |
| 4 | Rear liner | Blue rear liner on the drive side |
| 5 | Volute liner | Blue liner of the volute chamber |
| 6 | Pump casing | Metal casing outside the blue liner |
| 7 | Bearing | Bearing shown in the drive-end section |
| 8 | Pump shaft | Shaft running from the bearing frame to the impeller |
| Component |
|---|
| Expeller |
| Mechanical seal |
| Packed gland seal |
Models with the same components are grouped together; select a group to open its component table.
Models: KREBS slurryMAX-HP 10x8, KREBS slurryMAX-HP 12x10, KREBS slurryMAX-HP 14x12, KREBS slurryMAX-HP 16x14, KREBS slurryMAX-HP 4x4, KREBS slurryMAX-HP 6x6, KREBS slurryMAX-HP 8x6
| No. | Component |
|---|---|
| 1 | Impeller |
| 2 | Wear ring |
| 3 | Model-specific component |
| 4 | Rear liner |
| 5 | Model-specific component |
| 6 | Pump casing |
| 7 | Bearing |
| 8 | Pump shaft |
| Auxiliary Impeller | |
| Mechanical seal | |
| Model-specific component |
The slurryMAX-HP covers 7 models: KREBS slurryMAX-HP 10x8, KREBS slurryMAX-HP 12x10, KREBS slurryMAX-HP 14x12, KREBS slurryMAX-HP 16x14, KREBS slurryMAX-HP 4x4, KREBS slurryMAX-HP 6x6, KREBS slurryMAX-HP 8x6. Former and renamed designations are listed in the models table on this page.
The slurryMAX-HP is also documented under these designations: KREBS slurryMAX-HP 10x8, KREBS slurryMAX-HP 12x10, KREBS slurryMAX-HP 14x12, KREBS slurryMAX-HP 16x14, KREBS slurryMAX-HP 4x4, KREBS slurryMAX-HP 6x6, KREBS slurryMAX-HP 8x6.
The slurryMAX-HP is listed under the KREBS Cyclones and Slurry Pumps brand. Period: 2026-10-03. Status: Historical model.
11 components are recorded, including: Impeller, Wear ring, Rear liner, Pump casing, Auxiliary Impeller, Mechanical seal, Bearing, Pump shaft and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry