Potash/rock salt mining machine · 2011 · 3 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Kopeysk Ural-10R potash/rock salt mining machine | Урал-10Р | 2011 | 2 |
| Kopeysk Ural-20R potash/rock salt mining machine | Урал-20Р; Урал-20Р-14 | 2011 | 8 |
| Kopeysk Ural-61A potash/rock salt mining machine | Урал-61А | 2011 | 2 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Main cutting assembly | Front of machine | Урал-20Р-14 |
| 1 | Main cutting assembly | Front of machine | Урал-20Р |
| 1 | Main cutting assembly | Front of machine | Урал-10Р |
| 1 | Planetary-disc cutting assembly | Front of machine | Урал-61А |
| 2 | Crawler running gear | Beneath the body | Урал-20Р-14 |
| 2 | Side cutters | Sides of the main cutting assembly | Урал-20Р |
| 2 | Side milling cutter | Outer sides of cutting assembly | Урал-10Р |
| 2 | Crawler running gear | Beneath the body | Урал-61А |
| 3 | Crawler running gear | Beneath the body | Урал-20Р |
| Component |
|---|
| Electro-hydraulic control system (ILMA supply scope) |
| Double-stage reverse spiral cutting parts (source document cited) |
| Cutting drive (source document cited) |
| Reducer splined output shaft (source document quoted) |
| Side cutter mounting bushing (source document cited) |
| Bearings (source document cited) |
| End seal (source document cited) |
| Ural61A side Böhm milling cutter |
Models with the same components are grouped together; select a group to open its component table.
| No. | Component | Location |
|---|---|---|
| 2 | Side cutter (source document cited) | Spiral left and right sides, two pieces |
| Electro-hydraulic control system (ILMA supply scope) | Урал-20Р control, supply record since 2005 | |
| Double-stage reverse spiral cutting parts (source document cited) | Two spiral sections on a common pipe | |
| Cutting drive (source document cited) | Cutter drive on both sides, two sets | |
| Reducer splined output shaft (source document quoted) | Output terminal of each set of cutting drive reducer | |
| Side cutter mounting bushing (source document cited) | Installed on the splined output shaft and matched with the bearing inner ring | |
| Bearings (source document cited) | Connection position of output shaft and side cutter bushing | |
| End seal (source document cited) | When assembling the side cutter, install it on the bearing first |
| No. | Component | Location |
|---|---|---|
| 1 | Ural10R main cutting mechanism | The total power listed in the main actuator is 309kW |
| 2 | Ural10R side milling cutter | The outer width is based on the side milling cutter, and the exact tooth profile/material is not specified |
| No. | Component | Location |
|---|---|---|
| 1 | Ural61A planetary disc cutting mechanism | Main executing agency for potash/rock salt mining |
| Ural61A side Böhm milling cutter | Size column ширина по бермовым фрезам; number of teeth/specifications not included |
The Potash / rock-salt mining machine covers 3 models: Kopeysk Ural-10R potash/rock salt mining machine, Kopeysk Ural-20R potash/rock salt mining machine, Kopeysk Ural-61A potash/rock salt mining machine. Former and renamed designations are listed in the models table on this page.
The Potash / rock-salt mining machine is also documented under these designations: Kopeysk Ural-10R potash/rock salt mining machine, Урал-10Р, Kopeysk Ural-20R potash/rock salt mining machine, Урал-20Р, Урал-20Р-14, Kopeysk Ural-61A potash/rock salt mining machine, Урал-61А.
The Potash / rock-salt mining machine is listed under the Kopeysk brand as: Potash/rock salt mining machine. Period: 2011. Status: Listed in the manufacturer's current catalogue.
12 components are recorded, including: Ural10R side milling cutter, Ural10R main cutting mechanism, Electro-hydraulic control system (ILMA supply scope), Double-stage reverse spiral cutting parts (source document cited), Side cutter (source document cited), Cutting drive (source document cited), Reducer splined output shaft (source document quoted), Side cutter mounting bushing (source document cited) and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry