FLS HPGR Standard / HPGR Pro

Start with the PM model, roll diameter and width to identify roll wear systems, load-bearing and hydraulic spares, materials and drawing for quotation.

Official FLS HPGR Standard machine image
Official FLS HPGR Standard image. Models range from PM0 to PM10; confirm the installed machine by nameplate and serial number.
Official FLS HPGR Pro machine image
Official FLS HPGR Pro image. Check rotating side plates, skew limitation and oil lubrication against the upgrade scope.
Official FLS HPGR Pro front view
Official FLS HPGR Pro front view. Identify the installation through its feed hopper, rolls, hydraulic loading, bearings and drives on both sides.
OEM equipment guide

Ten Standard Models, Parts and Materials

The official FLS HPGR brochure lists roll diameter, width, grinding force, dual-motor power and overall dimensions for PM0, PM1 and PM3 to PM10. HPGR Pro features apply to new machines or confirmed Standard upgrade projects.

10HPGR Standard Models
950–3,000 mmRoll Diameter Range
650–2,000 mmRoll Width Range
2 × 220–5,000 kWDual-Motor Power Range
Models and key specifications

HPGR Standard PM0–PM10 Model Table

Dimensions are from the official FLS HPGR / HPGR Pro Upgrades brochure. For roll surfaces, bearings, hydraulics and drive spares, also verify serial number, fixed/floating roll position and upgrade configuration.

ModelSize DesignationRoll Diameter × Width (mm)Grinding Force (kN)Motor Power (kW)Length × Width × Height (mm)
PM09/7950 × 6502,7002 × 2203,240 × 1,860 × 3,800
PM111/81,100 × 8003,4002 × 4503,750 × 2,150 × 4,600
PM314/81,400 × 8004,3002 × 5003,735 × 2,164 × 5,400
PM417/101,700 × 1,0007,0002 × 8004,490 × 3,030 × 6,800
PM520/102,000 × 1,0008,6002 × 1,6005,950 × 3,000 × 7,500
PM620/152,000 × 1,50011,0002 × 1,8506,020 × 3,460 × 8,000
PM720/172,000 × 1,65013,5002 × 2,5006,550 × 3,640 × 8,800
PM824/172,400 × 1,65017,0002 × 2,8007,725 × 3,820 × 9,000
PM926/182,600 × 1,75020,0002 × 3,4008,500 × 4,150 × 9,700
PM1030/203,000 × 2,00025,0002 × 5,0009,500 × 4,600 × 11,000
HPGR Pro features include rotating side plates, mechanical skew limiters, stud detection, oil-lubricated main bearings and the AMPS machine-protection system. Verify applicability by machine size and project modification documents.
FLS

Component Location Diagram

The numbers on the diagram correspond one to one with the rows below.

FLS HPGR – Component Location Diagram
No.ComponentLocationApplies to
1Feed chute (lined)Feed passage above the rollsHPGR Standard
2Feed control gateLower feed chuteHPGR Standard
3Studded tireWorking surface of grinding rollsHPGR Standard
4Roll shaftCentreline of grinding rollsHPGR Standard
5Bearing blockSupports at the ends of the roll shaftsHPGR Standard
6Maintenance platformPlatform beside the roll assemblyHPGR Standard
7Hydraulic cylindersHydraulic loading beside the roll assemblyHPGR Standard
8Main drive motorRear drive endHPGR Standard
9Gear reducers with torque arm assemblyBetween the motors and roll shaftsHPGR Standard
10Cardan shaftDrive section between gear reducers and roll shaftsHPGR Standard
11Dust enclosure with inspection doorsEnclosure above the grinding rollsHPGR Standard
12Roll extraction frameExtraction rails below the machineHPGR Standard
Wear parts

Roll Surfaces, Studs, Side Plates and Chute Wear Systems

The roll centre, edges, side plates and feed/discharge passages have different wear mechanisms. The cards link part location and material choices to component pages; final confirmation follows the PM model and drawings.

Carbide Studs — identification image
02

Carbide Studs

Tungsten Carbide Stud

Embedded studs retain an autogenous protective material bed. Match diameter, length, head shape, spacing density, sockets and edge transitions.

View the Component Page →
Spare parts

Bearings, Hydraulics, Rolls and Dual-Side Drives

Distinguish HPGR Standard / Pro, PM model, machine side, fixed/floating roll and upgrade status. Only confirmed reference matches are published on component pages.

Hydraulic Cylinders and Seal Assemblies — identification image
02

Hydraulic Cylinders and Seal Assemblies

Hydraulic Cylinder & Seal Set

Load the roll gap and move the floating roll. Check bore, rod diameter, stroke, pressure, mounting trunnions, seal grooves and fluid.

View the Component Page →
Gearboxes, Couplings and Drive Shafts — identification image
04

Gearboxes, Couplings and Drive Shafts

Gearbox, Coupling & Drive Shaft

Identify each side of the dual-motor system as an assembly. Check power, ratio, output shaft, coupling, torque limitation and mounting datums.

View the Component Page →
FAQ

Frequently asked questions

How is an FLS HPGR model identified?

First check PM model and machine size, then roll diameter, width, serial number, surface type, fixed/floating roll position and Standard / Pro configuration.

Can HPGR Standard use Pro parts?

FLS states that machine sizes 4–10 can receive Pro upgrades. Each modification and part still requires checks against size, serial number, upgrade scope and modification drawings.

Can third-party roll-surface or stud references be checked?

Yes. Submit the reference, PM model, roll diameter and width, location, surface layout, used-part photographs and material data to establish a match.

Send FLS HPGR Model, Roll Layout, Drawing or Used-Part Details

Provide PM model, Standard / Pro, serial number, fixed/floating roll and side, surface layout, drawings or samples, material and duty. These support identification, material assessment, production at certified foundries, quality control and delivery.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry