Choose banana, horizontal, inclined, ultrafine or flip-flow screens to review screening media, wear parts, load-bearing structures, fasteners, support parts, materials and quotation requirements.
This page covers current series, published models and key dimensions, screening wear parts, and load-bearing and support spares relevant to supply. Manufacture and quotation still require the full model, serial number, drawing reference and installation drawings.
Where OEM literature provides only series capabilities, no model names are invented. Published GFF and UFS models and dimensions are listed separately for nameplate and installation checks.
| Series / Published Models | Design and Application | Key Dimensions or Capability |
|---|---|---|
| GFF single deck: GFF1861-1, 2461-1, 3061-1, 3661-1, 3673-1, 3690-1, 42100-1 | Linear-motion flip-flow screen; conventional protection decks and flip-flow decks can be configured | المعدات width × length from 1.8 × 6.1 m to 4.2 × 10.0 m |
| GFF double deck: GFF1861-2, 2461-2, 3061-2, 3661-2, 3673-2, 3690-2, 42100-2, 42120-2, 48120-2 | Flat or multi-slope decks for fine, moist and blinding-prone materials | المعدات width × length from 1.8 × 6.1 m to 4.8 × 12.0 m |
| UFS10、UFS8、UFS6、UFS4、UFS2 | Ultrafine wet screens with 10, 8, 6, 4 or 2 decks respectively | Screening areas 14 / 11.2 / 8.4 / 5.6 / 2.8 m²; screen body approximately 1.0 × 1.4 m |
| BSE | Banana screen with elliptical motion and high-acceleration screening | Maximum size capability published by the OEM: approximately 3.6 × 14.6 m |
| GMF / GLH | Engineered banana / horizontal linear-motion screens with 1, 2 or 3 decks | OEM-published width capability up to 4.9 m |
| ES (installation examples: ES302, ES403) / TSE | Horizontal elliptical-motion screens; TSE uses a compact three-shaft design | Published installation examples are not a complete model catalogue; verify parts by nameplate and serial number. |
| CVB / Compact CVB / RF | Inclined circular-motion screen series | OEM-published CVB installation angle range: 12°–22° |
| TS | Triple-slope banana screen | OEM-published deck slopes: 25° / 20° / 15° |
| EF / MF | Synchronised twin-drive elliptical-motion screen / mining banana screen | Identify by project configuration, decks, screening media and serial number. |
| FS / LH | Horizontal screen series | Identify by nameplate, full model, screen box and drive configuration. |
المعدات images identify series, screen boxes, decks and drive layouts. Use the component and material sections below for spare-part selection.
For high-throughput classification, with elliptical or linear motion and multi-slope decks depending on the series. Distinguish panels, liners and excitation systems by the specific series.
Includes elliptical and linear-motion configurations. Check drive arrangement, shaft layout, decks, screening dimensions and support structure.
Inclined circular-motion screens. Verify liners, media, vibrators and support parts against inclination, deck count and installed configuration.
GFF handles fine, moist or blinding-prone materials; UFS provides wet classification of fines at 0.075–1 mm. Their media materials and fastening systems must be distinguished.
Impact, sliding wear, blinding and corrosion vary between positions within one screen. Material links explain candidate options; general component pages support model- and drawing-based enquiries.
شبكة غربلة سلكية منسوجة Mesh
Withstands material impact, screening friction and repeated bending. Select wire material and diameter, aperture shape, tension direction and hook edges for particle size, corrosion and blinding. The image identifies the category; confirm against the full Metso model, serial number, part drawing, installation dimensions and interfaces.
View the General Component Page →
لوح غربلة من البولي يوريثان
Modular media for wet or dry screening. Open area, hardness, reinforcement, fastening and flow direction affect life; shape alone does not establish interchangeability. The image identifies the category; confirm against the full Metso model, serial number, part drawing, installation dimensions and interfaces.
View the General Component Page →
Modular Screen Panel System
Panels, support frames and fasteners form the screening surface together. Check module dimensions, apertures, flow direction, locking profile and support spacing. The image identifies the category; confirm against the full Metso model, serial number, part drawing, installation dimensions and interfaces.
View the General Component Page →
Capping Rubber
Between media and supports, these provide clamping, vibration isolation and separation of metal surfaces. Confirm section, hardness and length for the beam and panel configuration. The image identifies the category; verify the full Metso model, serial number, drawing, installation dimensions and interfaces.
View the General Component Page →
Side Plate Liner
Protect screen-box sides at feed and flow areas against particle erosion and local impact. Select wear plate, rubber or polyurethane for duty. The image identifies the category; verify the full Metso model, serial number, drawing, installation dimensions and interfaces.
View the General Component Page →
بطانة صندوق التغذية
The feed box is a high-impact area exposed to falling material, sliding particles and turning flow. Confirm thickness, joints, fastening holes and materials against drop height and feed size. The image identifies the category; verify the full Metso model, serial number, drawing, dimensions and interfaces.
View the General Component Page →
بطانة قناة التفريغ
At product discharge and transfer points, these resist continuous sliding wear, erosion and local impact. Select lining systems by particle size, speed, temperature and adhesion tendency. The image identifies the category; verify the full Metso model, serial number, drawing, dimensions and interfaces.
View the General Component Page →Verify spares by deck, load, fits, vibration, mounting interfaces and serial number. Exciter and bearing models without reliable images or drawing references are not presented as confirmed configurations.
Deck Frame / Crossmember
Support panels and transfer dynamic loads to the screen box. Check deck count, beam spacing, connection holes, weld design, fatigue requirements and corrosion protection. The image identifies the category; verify the full Metso model, serial number, drawing, dimensions and interfaces.
View the General Component Page →
قضيب شد / إسفين / Fastener
Maintain tension and position of tensioned mesh. Rail profile, hole spacing, wedge angle, bolt grade and orientation must match the box and media. The image identifies the category; verify the full Metso model, serial number, drawing, dimensions and interfaces.
View the General Component Page →
غلاف المحمل / Support Liner
Locate vibrator or exciter shafts and transmit loads. Check bores, centres, fits, lubrication, seals and mounting surfaces together. The image identifies the category; verify the full Metso model, serial number, drawing, dimensions and interfaces.
View the General Component Page →
Support Spring / Buffer
Isolate dynamic loads and maintain the screen's operating position. Confirm free height, stiffness, wire diameter, spring groups and rubber buffers as an installed set. The image identifies the category; verify the full Metso model, serial number, drawing, dimensions and interfaces.
View the General Component Page →Provide the full screen model, serial number, deck position, panel or mesh drawing reference, module dimensions, aperture shape and size, current material, fastening method and duty.
Length and width alone are insufficient. Check module profile, apertures, flow direction, fastening system, support-beam spacing, deck and drawing reference.
Provide the full screen model, serial number, vibrator or bearing nameplate, position, shaft configuration, current-part photographs and part number. The screen series alone is insufficient.
Browse component descriptions, drawing requirements and enquiry details.
Provide the full model, serial number, nameplate, deck and installation position, drawing reference, used-part photographs, key dimensions, current material and duty. These support identification, material assessment, manufacturing coordination, quality control and finished-part delivery.
رقم الهاتف: +86 156 3797 3199
zzx@anranst.com
توفر شركة ANRANST للعملاء العالميين تقييمات هندسية، واختيار التصنيع الصيني، ومراقبة الجودة، وتسليم الأجزاء النهائية لقطع الغيار الصناعية المقاومة للتآكل حسب الطلب، ويمكنها أيضًا دعم قطع الغيار الصناعية الأخرى حسب الطلب.
قم بمراجعة أسطح التزاوج وأبعاد الواجهة، وقم بتقييم جدوى المواد والمعالجة الحرارية والتصنيع.
تُحدَّد درجات المواد وعمليات المعالجة الحرارية لكل طلب على حدة، وتُثبَّت في الاتفاقية الفنية وتُتابَع أثناء الإنتاج.
يشمل ذلك تأكيد الرسم، ومراقبة المواد والعمليات، وتتبع الإنتاج، وتنسيق عمليات الفحص والقبول.
تنظيم عمليات التصنيع والتحقق من الجودة والتعبئة والتغليف وتسليم المنتجات النهائية الكاملة لتشكيل حلقة إمداد قابلة للتنفيذ.
قم بتزويدنا بالنماذج الحالية، والرسومات، وأرقام الرسومات، وأرقام الأجزاء، والمواد، أو معلومات ظروف التشغيل، وسنقوم بتحديد التحقق الفني ومسار التوريد وفقًا لذلك.
إرسال طلب