Cat 6015 – 6060 حفار التعدين الهيدروليكي الطرازات وقطع الغيار| ANRANST

Official Cat 6040 mine operating image showing the face-shovel attachment, bucket, cylinders, swing platform and crawler undercarriage.

Official Cat 6060 product image. Confirm each part by face-shovel or backhoe configuration, complete model, serial number and installed drawings.

Official Cat 6015 product image showing the backhoe attachment, pivots, cylinders and crawler undercarriage.

OEM المعدات التفاصيل

Identify face shovel or backhoe first, then bucket, attachment, swing and undercarriage position

A Cat model may have face-shovel or backhoe, diesel or electric, bucket and regional configurations. Teeth, adapters, shrouds, liners, pins, bushings, cylinders, swing and track parts require complete model, serial number, installation position and drawing revision. Tonnage or photographs alone do not establish interchangeability.

6 Current official models and power versions

14.6–61 t Published bucket payload

140–599 t Published operating weight

12 قطع الغيار المستهلكة and Key Spare Part Categories

Standard Models and Key Dimensions

Current Cat hydraulic mining shovel models and key parameters

Models, output, bucket payload and operating weight below come from Caterpillar's current catalogue and individual model pages, supporting initial machine and spare-part identification.

Standard Models	Engine/motor output	Rated bucket payload	Published operating weight
6015	615 kW	14.6 t	140 t
6020	776 kW	21.6 t	230.2 t
6030	1,230 kW	30 t	294 t
6040	1,550 kW	40 t	Approximately 411 t
6060	2,248 kW	61 t	599 t
6060 Electric	2 × 1,000 kW	61 t	580 t

Attachments, buckets, power, undercarriage and regional configurations vary across 6015–6060. Before manufacture or quotation, provide complete model, serial number, face shovel or backhoe, OEM or third-party drawing reference, revision and position.

قطع الغيار المستهلكة

Bucket edges, shrouds, liners and track wear parts

Official Cat images identify equipment and installation areas. Generic part images identify categories and do not establish Cat OEM interchangeability. Material options require confirmation by drawings, conditions and failure modes.

Bucket teeth

Bucket Teeth

Fit the cutting edge and withstand rock penetration impact, compression and high-stress abrasion. The image identifies a part category. Confirm complete Cat model, face shovel or backhoe, bucket specification, adapter system and existing dimensions.

Material Selection:Assess high-manganese steel, low-alloy wear-resistant cast steel or high-strength alloy steel according to impact energy, ore hardness, abrasiveness, tooth-breakage mode and heat-treatment capability.

فولاذ المنغنيز Chromium-Molybdenum Alloy Steel Special wear-resistant alloys

View the bucket tooth product page →

Tooth adapters

Tooth Adapters

Connect teeth to the bucket lip under repeated impact, bending and contact stress. Check tooth system, mounting angle, nose dimensions, pin structure, welding limits and lip fit.

Material Selection:Priorities are strength, toughness, hardenability and weld-zone reliability. Assess quenched and tempered low-alloy steel or wear-resistant cast steel; tooth appearance alone cannot determine material.

Chromium-Molybdenum Alloy Steel High-strength alloy steel

View tooth adapters →

Lip and edge shrouds

Lip & Edge Shrouds

Cover high-wear lip and leading-edge zones, resisting sliding wear and edge impact while protecting the structure. Check centre or side position, locks, coverage, clearances and adjacent teeth.

Material Selection:Wear-resistant alloy cast steel balancing abrasion and fracture resistance is a principal option. Confirm local material and hardness against block thickness, section changes and actual failure modes.

Chromium-Molybdenum Alloy Steel Special wear-resistant alloys

View lip shrouds →

Bucket internal liners and back guards

Bucket Liners & Back Shrouds

Provide replaceable floor, side, back and corner protection. The image does not establish Cat OEM interchangeability. Check segment drawings, thickness, curvature, holes, welding limits and wear maps.

Material Selection:Assess quenched and tempered wear plate for flat or formable liners and alloy castings for complex heavy blocks. Prioritise crack resistance and base support in high-impact zones.

Quenched and Tempered Wear Plate Wear-resistant alloy cast steel

View bucket liners →

Cutting and side edges

Cutting Edges & Side Cutters

Bottom and side edges carry digging, scraping and lateral impact loads. Check face-shovel or backhoe type, segments, hole spacing, counterbores, edge angle, thickness and adapter relationships.

Material Selection:Assess high-strength, tough wear plate or alloy cast steel. Meet edge hardness, core toughness, hole-edge crack resistance and replaceability requirements together.

Quenched and Tempered Wear Plate Chromium-Molybdenum Alloy Steel

View cutting edges →

Track Shoes

Track shoes carry ground loads, bending, impact and ground wear. The image is for category identification. Check model, width, hole spacing, pitch, ribs, connecting bolts and left/right assembly.

Material Selection:Large track shoes commonly use high-strength wear-resistant cast steel or forged/welded structures. Confirm the route with section, casting quality, heat treatment, surface hardness and non-destructive testing requirements.

Large load-bearing wear-resistant castings Chromium-Molybdenum Alloy Steel

View track shoes →

قطع الغيار

Pins, bushings, swing, hydraulic, undercarriage and structural spares

Group spares by attachment pivots, swing drive, hydraulics, undercarriage and load-bearing structure. Safety- and fatigue-critical parts require traceable materials, heat treatment, dimensions and inspection.

Bucket, stick and boom pins

Bucket, Stick & Boom Pins

Attachment pivot pins carry heavy oscillating loads, impact and boundary-lubricated contact. Check position, diameter, length, steps, lubrication holes, locks, surface damage and mating bushing bores.

Material Selection:Assess quenched and tempered high-strength alloy steel, induction hardening or other surface strengthening. Control surface hardness, effective case depth, core toughness, straightness and roughness together.

Alloy steels for pins and drives

View pins →

Pivot bushings and thrust parts

Pivot Bushings & Thrust Parts

Bushings and thrust parts serve boom, stick, bucket-linkage and cylinder-trunnion pivots. The image illustrates sliding bearings. Check diameters, length, oil grooves, interference, thrust faces and repaired bore condition.

Material Selection:Assess bearing copper alloys, steel-backed composites or original special bearing materials against loads, oscillating speed, lubrication, contamination and mating pins.

bearing copper alloys Engineering plastics and composite bearing materials

View bushings →

Slew bearings, ring gears and swing pinions

Swing Bearing, Ring Gear & Pinions

Upper-structure swing uses slew bearings, internal or external ring gears, pinions and reducers. The image identifies a large gear category. Check tooth count, module, pressure angle, profile shift, mounting holes, raceways and drive count.

Material Selection:Confirm gears and shafts by heavy-duty alloy steel with carburising or quench-and-temper treatment. Slew bearings also require raceway materials, heat treatment, preload, seals and bolt grade checks.

Alloy steel for heavy-duty gears and shafts

View gears, pinions and drive parts →

Hydraulic cylinders, piston rods and seal systems

Hydraulic Cylinders, Rods & الموانع

Boom, stick and bucket cylinders include barrels, rods, guide sleeves, pistons, cushions, seals and pipe interfaces. Provide cylinder number or position, bore, rod diameter, stroke, pressure and failure records.

Material Selection:Select rods by quenched and tempered alloy steel and surface strengthening, barrels by strength, honing and fatigue requirements, and seals by pressure, temperature, speed, media and contamination.

Alloy steel for hydraulic cylinder rods Hydraulic الموانع and Engineering Materials

View hydraulic seals and engineering materials →

Sprockets, track rollers, carrier rollers and idlers

Sprockets, Rollers & Idlers

Undercarriage sprockets, track and carrier rollers, and idlers face heavy loads, impact, mud and sand, and seal wear. The image identifies heavy-duty rollers only. Confirm undercarriage model and specific wheel position.

Material Selection:Confirm bodies and shafts by high-strength wear-resistant alloy steel, surface strengthening and core toughness. Check bearings, floating seals and lubrication as a complete assembly.

Alloy steel for heavy-duty shafts and wheel bodies Floating الموانع and Engineering Materials

View bearings, bushings and supports →

Boom, stick, bucket and load-bearing structures

Boom, Stick, Bucket & Structures

Booms, sticks, bucket lugs, links and underframes are fatigue-loaded structures. Repair or replacement requires complete drawings, base material, thickness, cast-steel nodes, weld class, stress relief, pin-bore coaxiality and non-destructive testing.

Material Selection:Structural plate, heavy cast-steel nodes, pins and wear protection follow different material and process routes. One wear-resistant grade cannot replace structural strength and fatigue checks.

Large load-bearing castings Wear-resistant and high-strength plate

View large structures and heavy-duty assemblies →

Are face-shovel and backhoe parts interchangeable on the same Cat model?

Do not assume so. Booms, sticks, buckets, links, cylinders and some pins and bushings differ. Confirm complete model, serial number, attachment configuration, position and drawing revision.

Is the model 6060 or 6040 enough to identify teeth and bucket shrouds?

No. Also provide face shovel or backhoe, bucket capacity and type, tooth or locking system, position, OEM or third-party number, used-part photos and key dimensions.

How can hydraulic mining shovel spares be identified without an OEM drawing number?

Provide machine nameplate, complete model and serial number, part position, assembly nameplate, photos, key dimensions, current material and failure records. Then assess whether catalogues, drawing searches or a physical survey can confirm the part.

Cat Hydraulic Mining Shovels: الطرازات وقطع الغيار