2012 · 6 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Jeffrey Rader EnduraHog ChipSizer CS | CS30; CS34; CS45; CS56 | 2012 | 7 |
| Jeffrey Rader EnduraHog Classic WB | WB34; WB45; WB55; WB56; WB58; WB66; WB68 | 2012 | 7 |
| Jeffrey Rader EnduraHog Flextooth FT | 30 FTE; 34 FTE; 45 FTE; 56 FTE; 59 FTE; 611 FT | 2012 | 7 |
| Jeffrey Rader EnduraHog Grinder AB | MME; 30ABE; 34ABE; 45ABE; 56ABE; 59ABE | 2012 | 7 |
| Jeffrey Rader EnduraHog SuperSlugger SS | SuperSlugger; SS | 2012 | 7 |
| Pennsylvania Crusher FBR | FBR 422; FBR 423; FBR 424; FBR 483; FBR 484; FBR 485; FBR 545; FBR 547; FBR 549 | 1988, 1994, 2000 | 9 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Hammer | Swing hammers around the rotor | Pennsylvania Crusher FBR |
| 1 | Hammer | Swing hammer on the rotor perimeter | EnduraHog Classic WB;EnduraHog Chip-Sizer CS;EnduraHog Flextooth FT;EnduraHog Grinder AB;EnduraHog SuperSlugger SS |
| 2 | Rotor disc | Discs along the rotor shaft | Pennsylvania Crusher FBR |
| 2 | Rotor disc | Disc at the centre of the rotor | EnduraHog Classic WB;EnduraHog Chip-Sizer CS;EnduraHog Flextooth FT;EnduraHog Grinder AB;EnduraHog SuperSlugger SS |
| 3 | Hammer pin | Pins passing through the outer rotor discs | Pennsylvania Crusher FBR |
| 3 | Rotor shaft | Centre shaft section of the rotor | EnduraHog Classic WB;EnduraHog Chip-Sizer CS;EnduraHog Flextooth FT;EnduraHog Grinder AB;EnduraHog SuperSlugger SS |
| 4 | Rotor shaft | Exposed shaft on the right | Pennsylvania Crusher FBR |
| 4 | Screen grate | Curved screen grate below the rotor | EnduraHog Classic WB;EnduraHog Chip-Sizer CS;EnduraHog Flextooth FT;EnduraHog Grinder AB;EnduraHog SuperSlugger SS |
| 5 | Bearing housing | Bearing support around the right-hand rotor shaft extension | Pennsylvania Crusher FBR |
| 5 | Frame liner | Replaceable liner inside the feed chamber | EnduraHog Classic WB;EnduraHog Chip-Sizer CS;EnduraHog Flextooth FT;EnduraHog Grinder AB;EnduraHog SuperSlugger SS |
| 6 | Screen plate | Opened screen cage in front of the rotor | Pennsylvania Crusher FBR |
| 6 | Breaker plate | Breaker plate above and to the right of the rotor | EnduraHog Classic WB;EnduraHog Chip-Sizer CS;EnduraHog Flextooth FT;EnduraHog Grinder AB;EnduraHog SuperSlugger SS |
| Component |
|---|
| Breaker block |
| Screen bar |
| Tramp-metal pocket |
Models with the same components are grouped together; select a group to open its component table.
Models: Jeffrey Rader EnduraHog ChipSizer CS, Jeffrey Rader EnduraHog Classic WB, Jeffrey Rader EnduraHog Flextooth FT, Jeffrey Rader EnduraHog Grinder AB, Jeffrey Rader EnduraHog SuperSlugger SS
| No. | Component |
|---|---|
| 1 | Hammer head |
| 2 | Rotor disc |
| 3 | Hammer shaft |
| 3 | Rotor shaft |
| 5 | Housing liner |
| 6 | Crushing plate |
| Screen bar |
| No. | Component |
|---|---|
| 1 | Hammer head |
| 2 | Rotor disc |
| 3 | Hammer shaft |
| 3 | Rotor shaft |
| 4 | Screen plate |
| 5 | Bearing housing |
| Model-specific component | |
| Screen bar | |
| Model-specific component |
The Hammer Crusher covers 6 models: Jeffrey Rader EnduraHog ChipSizer CS, Jeffrey Rader EnduraHog Classic WB, Jeffrey Rader EnduraHog Flextooth FT, Jeffrey Rader EnduraHog Grinder AB, Jeffrey Rader EnduraHog SuperSlugger SS, Pennsylvania Crusher FBR. Former and renamed designations are listed in the models table on this page.
The Hammer Crusher is also documented under these designations: Jeffrey Rader EnduraHog ChipSizer CS, CS30, CS34, CS45, CS56, Jeffrey Rader EnduraHog Classic WB, WB34, WB45, WB55, WB56, WB58, WB66, WB68, Jeffrey Rader EnduraHog Flextooth FT.
The Hammer Crusher is listed under the TerraSource Global brand. Period: 2012. Status: Historical model.
11 components are recorded, including: Hammer head, Hammer shaft, Rotor disc, Crushing plate, Screen bar, Housing liner, Rotor shaft, Bearing housing and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry