2023 · 9 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| STM VPM 0.3 | VPM 0.3 | 2023 | 6 |
| STM VPM 10 | VPM 10 | 2023 | 6 |
| STM VPM 100 | VPM 100 | 2023 | 6 |
| STM VPM 125 | VPM 125 | 2023 | 6 |
| STM VPM 25 | VPM 25 | 2023 | 6 |
| STM VPM 35 | VPM 35 | 2023 | 6 |
| STM VPM 5 | VPM 5 | 2023 | 6 |
| STM VPM 50 | VPM 50 | 2023 | 6 |
| STM VPM 75 | VPM 75 | 2023 | 6 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Grinding rotor | Rotating stages in lower chamber | VPMmill family; source Figure4 |
| 2 | Stator ring | Fixed rings at chamber wall | VPMmill family; source Figure4 |
| 3 | Grinding shell | Green hanging grinding shell | VPMmill family; source Figure4 |
| 4 | Slurry feed inlet | Feed passage at chamber bottom | VPMmill family; source Figure4 |
| Component |
|---|
| Shell liner |
| Main shaft |
| Gearbox |
| Grinding media |
Models with the same components are grouped together; select a group to open its component table.
Models: STM VPM 0.3, STM VPM 10, STM VPM 100, STM VPM 125, STM VPM 25, STM VPM 35, STM VPM 5, STM VPM 50, STM VPM 75
| No. | Component |
|---|---|
| 1 | Model-specific component |
| 2 | Model-specific component |
| Shell liner | |
| Main shaft | |
| Reducer | |
| Model-specific component |
The VPMmill covers 9 models: STM VPM 0.3, STM VPM 10, STM VPM 100, STM VPM 125, STM VPM 25, STM VPM 35, STM VPM 5, STM VPM 50, STM VPM 75. Former and renamed designations are listed in the models table on this page.
The VPMmill is also documented under these designations: STM VPM 0.3, VPM 0.3, STM VPM 10, VPM 10, STM VPM 100, VPM 100, STM VPM 125, VPM 125, STM VPM 25, VPM 25, STM VPM 35, VPM 35, STM VPM 5, VPM 5.
The VPMmill is listed under the Swiss Tower Mills Minerals brand. Period: 2023. Status: Historical model.
6 components are recorded, including: Shell liner, Main shaft, Reducer and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry