Centrifugal slurry pump · 2026-10-03 · 6 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| KREBS slurryMAX 10x8 centrifugal slurry pump | KREBS slurryMAX 10x8 Centrifugal slurry pump | 2026-10-03 | 11 |
| KREBS slurryMAX 12x10 centrifugal slurry pump | KREBS slurryMAX 12x10 Centrifugal slurry pump | 2026-10-03 | 11 |
| KREBS slurryMAX 3x2 centrifugal slurry pump | KREBS slurryMAX 3x2 Centrifugal slurry pump | 2026-10-03 | 11 |
| KREBS slurryMAX 4x3 centrifugal slurry pump | KREBS slurryMAX 4x3 Centrifugal slurry pump | 2026-10-03 | 11 |
| KREBS slurryMAX 6x4 centrifugal slurry pump | KREBS slurryMAX 6x4 Centrifugal slurry pump | 2026-10-03 | 11 |
| KREBS slurryMAX 8x6 centrifugal slurry pump | KREBS slurryMAX 8x6 Centrifugal slurry pump | 2026-10-03 | 11 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location |
|---|---|---|
| 1 | Impeller | Red wet-end impeller |
| 2 | Wear ring | In front of the impeller eye |
| 3 | Suction liner | Inside the suction inlet |
| 4 | Rear liner | Liner on the drive side of the impeller |
| 5 | Volute liner | Internal volute lining |
| 6 | Pump casing | Pressure casing outside the liners |
| 7 | Bearing | Inside the rear power frame |
| 8 | Pump shaft | Between the power frame and wet end |
| Component |
|---|
| Expeller |
| Mechanical seal |
| Packed gland seal |
Models with the same components are grouped together; select a group to open its component table.
Models: KREBS slurryMAX 10x8 centrifugal slurry pump, KREBS slurryMAX 12x10 centrifugal slurry pump, KREBS slurryMAX 3x2 centrifugal slurry pump, KREBS slurryMAX 4x3 centrifugal slurry pump, KREBS slurryMAX 6x4 centrifugal slurry pump, KREBS slurryMAX 8x6 centrifugal slurry pump
| No. | Component |
|---|---|
| 1 | Impeller |
| 2 | Wear ring |
| 3 | Model-specific component |
| 4 | Rear liner |
| 5 | Model-specific component |
| 6 | Pump casing |
| 7 | Bearing |
| 8 | Pump shaft |
| Auxiliary Impeller | |
| Mechanical seal | |
| Model-specific component |
The slurryMAX Centrifugal slurry pump covers 6 models: KREBS slurryMAX 10x8 centrifugal slurry pump, KREBS slurryMAX 12x10 centrifugal slurry pump, KREBS slurryMAX 3x2 centrifugal slurry pump, KREBS slurryMAX 4x3 centrifugal slurry pump, KREBS slurryMAX 6x4 centrifugal slurry pump, KREBS slurryMAX 8x6 centrifugal slurry pump. Former and renamed designations are listed in the models table on this page.
The slurryMAX Centrifugal slurry pump is also documented under these designations: KREBS slurryMAX 10x8 centrifugal slurry pump, KREBS slurryMAX 12x10 centrifugal slurry pump, KREBS slurryMAX 3x2 centrifugal slurry pump, KREBS slurryMAX 4x3 centrifugal slurry pump, KREBS slurryMAX 6x4 centrifugal slurry pump, KREBS slurryMAX 8x6 centrifugal slurry pump.
The slurryMAX Centrifugal slurry pump is listed under the KREBS Cyclones and Slurry Pumps brand as: Centrifugal slurry pump. Period: 2026-10-03. Status: Historical model.
11 components are recorded, including: Impeller, Wear ring, Rear liner, Pump casing, Auxiliary Impeller, Mechanical seal, Bearing, Pump shaft and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry