2026-10-03 · 12 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Period | Components |
|---|---|---|
| KREBS millMAX 10x8 | 2026-10-03 | 8 |
| KREBS millMAX 12x10 | 2026-10-03 | 8 |
| KREBS millMAX 14x12 | 2026-10-03 | 8 |
| KREBS millMAX 16x14 | 2026-10-03 | 8 |
| KREBS millMAX 18x16 | 2026-10-03 | 8 |
| KREBS millMAX 20x18 | 2026-10-03 | 8 |
| KREBS millMAX 24x20 | 2026-10-03 | 8 |
| KREBS millMAX 28x26 | 2026-10-03 | 8 |
| KREBS millMAX 3x2 | 2026-10-03 | 8 |
| KREBS millMAX 4x3 | 2026-10-03 | 8 |
| KREBS millMAX 6x4 | 2026-10-03 | 8 |
| KREBS millMAX 8x6 | 2026-10-03 | 8 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location |
|---|---|---|
| 1 | Impeller | Red impeller at the wet-end centre |
| 2 | Wear ring | Between the impeller eye and suction inlet |
| 3 | Suction liner | Suction-side internal wall |
| 4 | Pump casing | Outer metal casing of the wet end |
| 5 | Packed gland seal | Water-flush gland cavity shown in the section |
| 6 | Bearing | Bearing support inside the rear power frame |
| 7 | Pump shaft | Drive shaft from the power frame to the impeller |
| Component |
|---|
| Mechanical seal |
Models with the same components are grouped together; select a group to open its component table.
Models: KREBS millMAX 10x8, KREBS millMAX 12x10, KREBS millMAX 14x12, KREBS millMAX 16x14, KREBS millMAX 18x16, KREBS millMAX 20x18, KREBS millMAX 24x20, KREBS millMAX 28x26, KREBS millMAX 3x2, KREBS millMAX 4x3, KREBS millMAX 6x4, KREBS millMAX 8x6
| No. | Component |
|---|---|
| 1 | Impeller |
| 2 | Wear ring |
| 3 | Model-specific component |
| 4 | Pump casing |
| 5 | Model-specific component |
| 6 | Bearing |
| 7 | Pump shaft |
| Mechanical seal |
The millMAX covers 12 models: KREBS millMAX 10x8, KREBS millMAX 12x10, KREBS millMAX 14x12, KREBS millMAX 16x14, KREBS millMAX 18x16, KREBS millMAX 20x18, KREBS millMAX 24x20, KREBS millMAX 28x26, KREBS millMAX 3x2, KREBS millMAX 4x3, KREBS millMAX 6x4, KREBS millMAX 8x6. Former and renamed designations are listed in the models table on this page.
The millMAX is also documented under these designations: KREBS millMAX 10x8, KREBS millMAX 12x10, KREBS millMAX 14x12, KREBS millMAX 16x14, KREBS millMAX 18x16, KREBS millMAX 20x18, KREBS millMAX 24x20, KREBS millMAX 28x26, KREBS millMAX 3x2, KREBS millMAX 4x3, KREBS millMAX 6x4, KREBS millMAX 8x6.
The millMAX is listed under the KREBS Cyclones and Slurry Pumps brand. Period: 2026-10-03. Status: Historical model.
8 components are recorded, including: Impeller, Wear ring, Pump casing, Mechanical seal, Bearing, Pump shaft and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry