2026-10-03 · 6 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Period | Components |
|---|---|---|
| KREBS millMAX-HH 10x8 | 2026-10-03 | 8 |
| KREBS millMAX-HH 12x10 | 2026-10-03 | 8 |
| KREBS millMAX-HH 3x2 | 2026-10-03 | 8 |
| KREBS millMAX-HH 4x3 | 2026-10-03 | 8 |
| KREBS millMAX-HH 6x4 | 2026-10-03 | 8 |
| KREBS millMAX-HH 8x6 | 2026-10-03 | 8 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location |
|---|---|---|
| 1 | Impeller | Impeller in the HH concentric wet end |
| 2 | Pump casing | HH concentric pressure casing |
| Component |
|---|
| Wear ring |
| Suction liner |
| Mechanical seal |
| Packed gland seal |
| Bearing |
| Pump shaft |
Models with the same components are grouped together; select a group to open its component table.
Models: KREBS millMAX-HH 10x8, KREBS millMAX-HH 12x10, KREBS millMAX-HH 3x2, KREBS millMAX-HH 4x3, KREBS millMAX-HH 6x4, KREBS millMAX-HH 8x6
| No. | Component |
|---|---|
| 1 | Impeller |
| 2 | Pump casing |
| Wear ring | |
| Model-specific component | |
| Mechanical seal | |
| Model-specific component | |
| Bearing | |
| Pump shaft |
The millMAX-HH covers 6 models: KREBS millMAX-HH 10x8, KREBS millMAX-HH 12x10, KREBS millMAX-HH 3x2, KREBS millMAX-HH 4x3, KREBS millMAX-HH 6x4, KREBS millMAX-HH 8x6. Former and renamed designations are listed in the models table on this page.
The millMAX-HH is also documented under these designations: KREBS millMAX-HH 10x8, KREBS millMAX-HH 12x10, KREBS millMAX-HH 3x2, KREBS millMAX-HH 4x3, KREBS millMAX-HH 6x4, KREBS millMAX-HH 8x6.
The millMAX-HH is listed under the KREBS Cyclones and Slurry Pumps brand. Period: 2026-10-03. Status: Historical model.
8 components are recorded, including: Impeller, Wear ring, Pump casing, Mechanical seal, Bearing, Pump shaft and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry