01
Ring Hammer
Ring Hammer / Ring
A general wear part category for Granulator. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →Astec Granulator
Start with the brand, equipment series and installed machine, then explore wear parts, drive and structural spares, materials and processes, drawing review, quality control and finished-part delivery.
OEM Equipment Series
Identify the Machine, Then Select Parts and Materials
This page covers equipment series and models, part locations, materials and processes, drawing review and inquiry options. Before manufacture or quotation, confirm drawing, dimensions and tooling suitability against the complete model and drawings.
TKK Granulator TKKGeneral Equipment Categories
1Equipment Identification Entries
6Related Wear Parts
2Related Spare Parts
Models and Identification
Granulator Series and Installed Equipment
The model table assists with machine identification. Manufacture and quotation require the nameplate, complete model, serial number, drawing, general arrangement and drawing revision.
| Series / Model | Equipment Range and Identification | Equipment History and Identification |
|---|---|---|
| Granulator | Use the complete model, serial number, drawing and general arrangement together to identify the installed equipment | Identify the installed machine from its equipment records |
Astec Industries
Component Location Diagram
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to | |
|---|---|---|---|---|
| 1 |  | Ring hammer | Rows of ring hammers on the TKK rotor perimeter | TKK / Koal-King |
| 2 | Screen cage | Screening zone below and beside the rotor | TKK / Koal-King | |
| 3 | Crushing shaft | Centerline of the rotating shaft in the crushing chamber | TKK / Koal-King | |
| 4 | Bearing housing | External support housing at the shaft end | TKK / Koal-King | |
| 5 | Housing | External equipment housing | TKK / Koal-King |
Wear Parts
Identify Wear Parts by Installation Position
These general Granulator part categories help identify the part you need. Confirm suitability against the specific Astec model and drawings.
02
Hammer Pin
Hammer Pin / Rotor Pin
A general wear part category for Granulator. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →03
Screen Plate / Grate Plate
Screen Plate / Grate Plate
A general wear part category for Granulator. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →04
Impact Plate / Breaker Plate
Impact Plate / Breaker Plate
A general wear part category for Granulator. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →05
Side Liners
Side Liner
A general wear part category for Granulator. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →06
Housing Liners
Housing Liner
A general wear part category for Granulator. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →Spare Parts
Drive, Load-Bearing and Structural Parts
Identify gears, shafts, sleeves, bearings, seals, hydraulic parts, supports and connectors for drawing review. Listed OEM drawing or part references relate to identified parts and require confirmation against your machine.
01
Hammer Pin
Hammer Pin / Rotor Pin
A general structural or drive part category for Granulator. Confirm interfaces, accuracy, material and applicable model against the equipment drawings.
View General Part Details →02
Bearing / Bearing Housing
Bearing / Bearing Housing
A general structural or drive part category for Granulator. Confirm interfaces, accuracy, material and applicable model against the equipment drawings.
View General Part Details →FAQ
Frequently asked questions
What information is needed to quote parts for Astec Granulator?
Provide the complete model, serial number, drawing revision, installation position, photographs of the current part, material and operating conditions.
Can a general part image be used directly for manufacture?
No. General images help identify the part category. Manufacture requires agreed drawings, dimensions, interfaces, materials and acceptance criteria.
Can a part be assessed without an drawing?
Start with the nameplate, general arrangement drawing, installation position, used-part photographs and key dimensions. We can then assess the feasibility of dimensional inspection, material evaluation and manufacture to drawing.