2016 · 3 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| AARD 10 LHD | 2016 | 1 | |
| AARD 5.5 LP LHD | AARD 55 LP LHD; Epiroc LHD 5.5 LP | 2026 Epiroc | 10 |
| AARD 7 LP LHD | AARD 7 LHD | 10 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Bucket | Front loading implement of the scoop or LHD | 5.5 LP LHD |
| 2 | Tyre | Exposed tyre of the vehicle running gear | 5.5 LP LHD |
| 3 | Lift cylinder | Between the LHD frame and bucket lift arm | 5.5 LP LHD |
| 4 | Bucket tilt cylinder | Hydraulic actuator for the bucket tilt linkage | 5.5 LP LHD |
| Component |
|---|
| Diesel engine |
| Transmission and torque converter |
| Drive axle |
| Brake |
| Hydraulic pump |
| Filter |
Models with the same components are grouped together; select a group to open its component table.
Models: AARD 5.5 LP LHD, AARD 7 LP LHD
| No. | Component | Location |
|---|---|---|
| 1 | Bucket | Front loading position |
| 2 | Tire | |
| 3 | Model-specific component | |
| 4 | Model-specific component | |
| Model-specific component | ||
| Model-specific component | ||
| Model-specific component | ||
| Brake | ||
| Hydraulic Pump | ||
| Model-specific component |
| No. | Component | Location |
|---|---|---|
| 1 | Bucket | Front loading position |
The AARD Underground Load-Haul-Dump Machines covers 3 models: AARD 10 LHD, AARD 5.5 LP LHD, AARD 7 LP LHD. Former and renamed designations are listed in the models table on this page.
The AARD Underground Load-Haul-Dump Machines is also documented under these designations: AARD 10 LHD, AARD 5.5 LP LHD, Epiroc LHD 5.5 LP, AARD 7 LP LHD, AARD 7 LHD.
The AARD Underground Load-Haul-Dump Machines is listed under the AARD brand. Period: 2016. Status: Historical model.
10 components are recorded, including: Brake, Tire, Hydraulic Pump, Bucket and more. The full list with locations is in the components table on this page.
Model-specific components with their own page: Bucket (1 in total).
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry