METSO · Détails de la pièce

Pinion

Pinion

Identify parts for Metso cone crushers, check models and drawing, confirm materials and processes, and submit an inquiry.

Équipements et modèles applicables

Identifiez le modèle installé et les dimensions clés, puis vérifiez la révision du plan et les interfaces physiques.

Equipment Series

Metso Cone Crushers

Models and Key Dimensions

Metso HP Series (HP100-HP800), GP Series (GP100-GP550) and MP Series

Matériaux et procédés

Select the material grade and heat treatment for the operating conditions, processed material and equipment specifications. The options below are commonly used; confirm the final grade against the drawing and technical agreement.

Alloy steel 42CrMo4 (EN 10083-3)

Candidate material for forged steel pinions; quenching and tempering, tooth surface hardening and mechanical property requirements depend on loading, dimensions and the drawing.

Alloy steel 20CrMnTi

Carburizing gear steel; verify effective case depth and surface and core hardness against the gear drawing and load requirements.

Alloy steel 34CrNiMo6 (EN 10083-3)

Candidate quenched and tempered alloy steel; suitability and mechanical properties depend on drive loads, section size and drawing requirements.

Caractéristiques d'usure et remplacement

Modes d'usure et conseils d'entretien courants ; le cycle réel dépend des conditions, du matériau et des données de fonctionnement.

Modes d'usure courants

  • Tooth flank contact fatigue begins as small pits and can progress to extensive spalling
  • Tooth flank scoring: inadequate lubrication under high speed and heavy loading causes local welding and tearing
  • Tooth root bending fatigue: repeated pulsating loads cause root cracks and can lead to broken teeth
  • Abrasive tooth flank wear: contaminated oil accelerates surface material loss
Critères de remplacement

Assess replacement against the pitting, tooth thickness and backlash limits in the gear drawings and maintenance specification. Replace immediately if tooth root cracks occur. Inspect the pinion and gear together for wear and meshing condition.

Contrôle matière et procédé

Les exigences matière, traitement thermique, procédés composites et contrôles suivent le plan, les conditions et le contrôle technique.

Material Grade / Substrate

Alloy steel 42CrMo4 (EN 10083-3), alloy steel 20CrMnTi and alloy steel 34CrNiMo6 (EN 10083-3)

Heat Treatment Condition

Quenching and tempering, tooth or surface induction hardening, or carburizing and quenching. Verify final hardness and microstructure against the drawing and technical agreement.

Composite / Hardfacing Requirements

Repair eligibility, procedures and acceptance criteria for high-manganese steel liners must follow the specific part drawing and an approved repair plan. Ceramic tiles and composite plates are not universal substitutes.

Dimensions and Inspection

Manufacture to drawings produced from part measurements or supplied by the customer. Critical mating surface tolerances follow OEM requirements. Use UT/MT inspection to assess castings for shrinkage porosity and cracks against the agreed acceptance criteria.

Des pièces de même nom peuvent ne pas être interchangeables selon le modèle, la révision du plan, les interfaces et les exigences matière. Avant fabrication, se baser sur le modèle complet, le numéro de série et les plans.

Send Your Wear Part Requirements

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry