KVS air-swept ball / tube mills

Air swept ball tube mill · 2006 · 1 model

Kennedy Van Saun KVS air-swept ball / tube mills – Air swept ball tube mill
Kennedy Van Saun KVS air-swept ball / tube mills – Air swept ball tube mill (2)
Kennedy Van Saun
Kennedy Van SaunBrand
Air swept ball tube millEquipment type
2006Period
Historical modelStatus
Kennedy Van Saun

Models and Historical Names in This Series

Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.

ModelHistorical names / renamingsPeriodComponents
KVS air-swept ball / tube millsKVS Kendal 15 5 ×22 1; KVS Kendal200671
Kennedy Van Saun

Numbered Components

The numbers on the diagram correspond one to one with the rows below.

No.ComponentLocationApplies to
1Feed / discharge boxesConnection box at the left end of the mill in the side view
2Ball-charge hopperBall-charge hopper above the left-hand end in the side view
3Girth gearOuter circumference at the right-hand mill end in the side view
4Silencer housingEnclosure around the mill in the right-hand end view
5Mill connecting ductworkInlet ductwork from the coal bunker in the side view
6Trunnion bearingsSupport beneath the mill end in the side view
Other Components · 35 items
Component
Feeding box lining
Hollow bushing
steel ball
Pinion Bearing
Main drive reducer
Falk high speed and low speed coupling
Forced lubrication oil tank
Forced lubrication gear pump
Lubrication pump drive motor
Double basket oil filter
Tubular oil cooler
Oil distributor inside the reduction gearbox
Forced lubrication pressure relief valve group
Ring gear automatic grease lubrication system
Grease spray air solenoid valve
Ring gear grease pump
Ring gear air atomization nozzle
Turning worm reducer
Turning drive motor
Turning magnetic brake and brake drum
Turning gear coupling
Classifier high wear surface ceramic patch
Coarse powder return pipe inclined section lining
Silencer shell thermal insulation and sound insulation layer
Silencer shell access door
Silencer shell inspection hole cover
Ball filling hopper isolation valve
Ball replenishing hopper chute
Sealed air fan
Sealed air blower motor
Sealed fan intake silencer filter group
Sealed fan gear coupling
Pinion shaft seal
Pinion seal water seal ring
Pinion shaft stuffing box
Kennedy Van Saun

Components by Model

Models with the same components are grouped together; select a group to open its component table.

KVS air-swept ball / tube mills71 items
No.ComponentLocation
1Feeding and discharging box bodyMaterial inlet and outlet connection; the original registered liner is retained.
2Steel ball loading hopper bodyThe hopper for replenishing balls to the mill. The two ball charge hoppers in the text are summarized by one part.
3Girth gearExternal drive side of grinding shell
4Silencer housingmill silencer housing
5Mill connecting duct air duct groupThree paths from the feeding valve to the mill, the mill discharges to the classifier, and the coarse powder returns to the feeding box
Feeding box liningFeeding box discharge side and feeding plate
Hollow bushingThe inside of the mill inlet and outlet journal
steel ballInside the mill barrel
Pinion BearingDrive pinion support
Main drive reducerMill transmission chain; Chapter 7 single-stage helical gear
Falk high speed and low speed couplingMain drive high speed/low speed side; two similar positions are registered together
Forced lubrication oil tankUnder the reducer and pinion bearing lubrication system
Forced lubrication gear pumpThe oil tank supplies oil and supplies pressure oil to the reduction box and pinion bearings.
Lubrication pump drive motorGear pump drive
Double basket oil filterAfter the pump, before the oil cooler
Tubular oil coolerOil supply to main reduction box and pinion bearing after filter
Oil distributor inside the reduction gearboxInternal oil supply of main reduction gearbox
Forced lubrication pressure relief valve groupFilter/cooler bypass and pressure adjustment
Ring gear automatic grease lubrication systemGrease spraying on the pressure tooth surface of the ring gear
Grease spray air solenoid valveControlled by electrical switch board timer
Ring gear grease pumpPneumatic pump supplies grease from 50 or 180kg grease container; two container specifications are optional
Ring gear air atomization nozzleGrease spraying on the pressure tooth surface of the ring gear
Turning worm reducerbarring gear system
Turning drive motorTurning worm reducer drive
Turning magnetic brake and brake drumBetween motor and worm reducer
Turning gear couplingWorm reducer low speed shaft and one end of double output shaft motor
Classifier high wear surface ceramic patchHigh wear surface of classifier
Coarse powder return pipe inclined section liningInclined section leading to mill feed box
Silencer shell thermal insulation and sound insulation layerInsulation/sound insulation structure within the sound-absorbing shell that meets the 85dB(a) requirement for this example
Silencer shell access doorSilencer shell access door
Silencer shell inspection hole coverinspection hole with cover; hole is not regarded as another part
Ball filling hopper isolation valveThe connection between the hopper and the ball filling machine
Ball replenishing hopper chuteHopper to mill feeding/discharging box
Sealed air fanSealing air supply for various parts of the mill; supporting the mill system
Sealed air blower motorFan driver
Sealed fan intake silencer filter groupAir intake silencer with filter
Sealed fan gear couplingFan drive connection
Pinion shaft sealpinion gear seals in checklist
Pinion seal water seal ringlantern rings, seal inspection object; descriptive Chinese name reserved in English
Pinion shaft stuffing boxstuffing box alignment/gap check
Ring gear lubrication drip pandrip trays need cleaning
Grease spray distribution proximity switchMonitoring the moving plunger, the example clearance is given in the table
Grease dispensing moving plungermoving plunger, opposite to proximity switch
Grease injection system filterClear objects in the trainers table
Ring gear sealing devicegirth gear sealing arrangement integrity/air leakage inspection in the table
Reduction box coupling protective coverTable 19-11 Disassembly and assembly of high-speed/low-speed coupling protection
Reduction box coupling springThe high-speed/low-speed coupling disassembly and inspection list clearly indicates coupling springs; do not create a new coupling series based on this
Reduction gearbox upper and lower half shellsRemove the upper half shell, clean both halves and then reassemble
Reducer box joint surface positioning pinTwo M20 positioning pins for casing joint
Reduction gearbox input end coverinput line end cover
Reduction gearbox fuel injection gun barrelRemove the oil spray lance flange joint
Reduction box pinion shaftpinion shaft lifting out inspection
Reduction box oil sealOil seals removed after removing the labyrinth cover
Reduction box shaft stop platekeeper plate is located at the non-drive end
Reduction box shaft locking nutdrive end locknut
Reduction gearbox input and output bearing setThe table specifies the axial clearance of the bench and installation respectively; the quantity/type is not completely listed
Reduction box output shaft assemblyLift the output shaft assembly vertically from the box
Gasket for central joint surface of reduction gearboxCentral joint surface of composite cabinet
Double cone classifierMill exhaust pulverized coal classification system
Forced lubrication control monitoring instrument clusterPressure switch, thermometer, flow indicator, pressure gauge, thermostat and sensor alarm
Grease injection compressed air treatment groupFiltration, pressure regulation and lubrication before grease injection pump
Grease injection progressive single line distributorGrease separation at the rear of the pump towards the nozzle
Grease injection timing and alarm control systemElectrical switch board timing, low air pressure/nozzle line high pressure/pump duration abnormal alarm and shutdown interlock
Double cone classifier manually adjustable blade setManual adjustment of blades in classifier
Double cone classifier guide vane setdeflector vanes
Double cone classifier inner and outer conesComposition of inner and outer cones of classifier
Classifier coarse powder return pipereject line connected to mill feed box
Classifier coarse powder cut-off gatecut-off gate on coarse powder return pipe
Mill bypass vent door assemblymill bypass damper assemblies
Reduction gearbox oil collectoroil catcher
Reduction gearbox oil collector labyrinth coverlabyrinth cover removed from oil collector

Frequently asked questions

What other names or designations is the KVS air-swept ball / tube mills known by?

The KVS air-swept ball / tube mills is also documented under these designations: KVS Kendal 15 5 ×22 1, KVS Kendal.

Which brand and type of equipment is the KVS air-swept ball / tube mills?

The KVS air-swept ball / tube mills is listed under the Kennedy Van Saun brand as: Air swept ball tube mill. Period: 2006. Status: Historical model.

Which components and wear parts are recorded for the KVS air-swept ball / tube mills?

71 components are recorded, including: Feeding box lining, Hollow bushing, steel ball, Girth gear, Pinion Bearing, Feeding and discharging box body, Steel ball loading hopper body, Main drive reducer and more. The full list with locations is in the components table on this page.

Which model-specific components of the KVS air-swept ball / tube mills have their own page?

Model-specific components with their own page: Double cone classifier, Forced lubrication control monitoring instrument cluster, Grease injection compressed air treatment group, Grease injection progressive single line distributor, Grease injection timing and alarm control system, Double cone classifier manually adjustable blade set, Double cone classifier guide vane set, Double cone classifier inner and outer cones and more (13 in total).

How do I enquire about parts for the KVS air-swept ball / tube mills?

Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.

Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry