Start with the brand, equipment series and installed machine, then explore wear parts, drive and structural spares, materials and processes, drawing review, quality control and finished-part delivery.
This page covers equipment series and models, part locations, materials and processes, drawing review and inquiry options. Before manufacture or quotation, confirm drawing, dimensions and tooling suitability against the complete model and drawings.
The model table assists with machine identification. Manufacture and quotation require the nameplate, complete model, serial number, drawing, general arrangement and drawing revision.
| Series / Model | Equipment Range and Identification | Equipment History and Identification |
|---|---|---|
| 220 SM | Medium surface miner with a cutting width of 2.2 m; standard configuration | Wirtgen Product Range |
| 220 SMi | 220 SMi surface miner; engine emissions configuration differs from the 220 SM. Identify the version from regional specifications and the nameplate | Wirtgen Product Range |
| 220 SM 3.8 | 220 SM wide-cut configuration with a cutting width of 3.8 m | Wirtgen Product Range |
| 220 SMi 3.8 | 220 SMi wide-cut configuration with a cutting width of 3.8 m | Wirtgen Product Range |
| 280 SM | Large surface miner with a cutting width of 2.75 m | Wirtgen Product Range |
| 280 SMi | 280 SMi surface miner; identify by nameplate and engine emissions configuration | Wirtgen Product Range |
| 4200 SM | Large surface miner with a cutting width of 4.2 m | Wirtgen Product Range |
| 4200 SMi | 4200 SMi surface miner; identify by nameplate and engine emissions configuration | Wirtgen Product Range |
| 260 SX / 260 SXi | Cross application miner; provide the regional version, nameplate and drawings when ordering cutting tools and spare parts | Wirtgen Product Range |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Cutting drum | Cutting drum at machine center | 260SX; 260SXi |
| 2 | Point-attack pick | Point-attack picks on drum surface | 260SX; 260SXi |
| 3 | HT14 toolholder upper part | Removable upper holder receiving pick | 260SX; 260SXi |
| 4 | HT14 welded holder base | Welded base supporting upper holder | 260SX; 260SXi |
| 5 | Discharge conveyor | Elevated discharge conveyor at rear | 260SX; 260SXi |
| 6 | Crawler track unit | Crawler unit beneath chassis | 260SX; 260SXi |
These general Surface Miner part categories help identify the part you need. Confirm suitability against the specific WIRTGEN model and drawings.
Cutting Tooth
A general wear part category for Surface Miner equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →Drum Liner
A general wear part category for surface miners. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →
Conveyor Scraper
A general wear part category for Surface Miner equipment. Confirm the installation position, profile, hole pattern, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →Deflector Plate
A general wear part category for surface miners. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →Chain Wear Parts
A general wear part category for surface miners. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →Base Plate Liner
A general wear part category for surface miners. Confirm the installation position, profile, hole pattern, material and applicable model against the equipment drawings.
View General Part Details →Identify gears, shafts, sleeves, bearings, seals, hydraulic parts, supports and connectors for drawing review. Listed OEM drawing or part references relate to identified parts and require confirmation against your machine.
Tool Holder
A general structural or drive part category for Surface Miner equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →
Cutting Edge
A general structural or drive part category for Surface Miner equipment. Confirm interfaces, accuracy, material and machine model against the equipment drawing. The image illustrates a part category and is not an OEM drawing.
View General Part Details →Provide the complete model, serial number, drawing revision, installation position, photographs of the current part, material and operating conditions.
No. General images help identify the part category. Manufacture requires agreed drawings, dimensions, interfaces, materials and acceptance criteria.
Start with the nameplate, general arrangement drawing, installation position, used-part photographs and key dimensions. We can then assess the feasibility of dimensional inspection, material evaluation and manufacture to drawing.
Provide the complete model, serial number, nameplate, installation position, photographs of the current part, drawings, material and operating conditions. We use these to identify the part, assess materials, organize production at certified foundries, coordinate quality control and arrange finished-part delivery.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry