Vibrating screen · 2026-10-03 · 4 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Vibrating screen | Inclined Grizzly Screen; 5 x16 8 x24; 2 | 2026-10-03 | 6 |
| Specmaker / three-shaft horizontal screen | Specmaker; Triple-shaft Horizontal Screen; 5 x16 8 x20; 3 | 2005, 2015–2019 | 6 |
| Valu-King inclined screen | Valu-King; 3 x6 6 x16 | 2026-10-03 | 5 |
| Vibro-King / Vibro-King TL inclined screen | Vibro-King; Vibro-King TL; 5 x16 8 x24; 2, 3, 4 | 2026-10-03 | 7 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Side plate | Long side plate of screen box | Vibro-King TL (2015 OEM brochure configuration) |
| 2 | Support spring | Support spring near feed end | Vibro-King TL (2015 OEM brochure configuration) |
| 3 | Vibrator shaft end | Visible vibrator shaft end on side plate | Vibro-King TL (2015 OEM brochure configuration) |
| 4 | Screen mesh | Visible screening deck at right | Vibro-King TL (2015 OEM brochure configuration) |
| Component |
|---|
| Screen deck cross beam |
| Bearing |
| Exciter shaft |
| Non-contact seal |
| Feed box liner |
| Grizzly bar |
| Synchronising gear |
Models with the same components are grouped together; select a group to open its component table.
| No. | Component |
|---|---|
| 2 | Support spring |
| 4 | Screen mesh |
| Model-specific component | |
| Bearing | |
| Exciter shaft | |
| Non-contact seal | |
| Feed box liner |
| No. | Component |
|---|---|
| 2 | Support spring |
| 4 | Screen mesh |
| Model-specific component | |
| Bearing | |
| Exciter shaft | |
| Bar |
| No. | Component |
|---|---|
| 2 | Support spring |
| 4 | Screen mesh |
| Model-specific component | |
| Bearing | |
| Exciter shaft | |
| Synchronizing gear |
| No. | Component |
|---|---|
| 2 | Support spring |
| 4 | Screen mesh |
| Model-specific component | |
| Bearing | |
| Exciter shaft |
The Vibrating screen covers 4 models: Vibrating screen, Specmaker / three-shaft horizontal screen, Valu-King inclined screen, Vibro-King / Vibro-King TL inclined screen. Former and renamed designations are listed in the models table on this page.
The Vibrating screen is also documented under these designations: Inclined Grizzly Screen, 5 x16 8 x24; 2, Specmaker / three-shaft horizontal screen, Specmaker, Triple-shaft Horizontal Screen, 5 x16 8 x20; 3, Valu-King inclined screen, Valu-King, 3 x6 6 x16, Vibro-King / Vibro-King TL inclined screen, Vibro-King, Vibro-King TL, 5 x16 8 x24; 2, 3, 4.
The Vibrating screen is listed under the Telsmith brand as: Vibrating screen. Period: 2026-10-03. Status: Historical model.
9 components are recorded, including: Screen mesh, Bearing, Exciter shaft, Support spring, Bar, Synchronizing gear, Non-contact seal, Feed box liner and more. The full list with locations is in the components table on this page.
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry