2013 · 7 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Strommashina model | 2013 | 3 | |
| Strommashina model | 2013 20 t / h | 2013 | 3 |
| Strommashina model | 2013 15 t / h | 2013 | 4 |
| / | 2013 | 5 | |
| 2–5 μm | 2013 5 t / h | 2013 | 7 |
| МП / СТРОМ-МИН | МП-1; МП-2; СТРОМ-МИН-8; СТРОМ-МИН-15; СТРОМ-МИН-30 | 2013 | 5 |
| ВНВ | 2013 | 2 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Bag filter | Filtering unit at the upper left of the process layout | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| 2 | Ball mill | Horizontal grinding machine beneath the feed hopper | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| 3 | Bucket elevator | Vertical elevator to the right of the mills | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| 4 | Silo | Storage vessels on the right of the layout | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| 5 | Cyclone dust collector | Cyclone at the upper centre of the layout | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| 6 | Conveyor belt | Horizontal belt feeders beneath the feed hopper | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| 7 | Screw conveyor | Conveying section from the mills to the elevator | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| 8 | Induced-draught fan | Fan to the left of the filter | 15 t/h dry grinding line for inert materials (standard model number not specified) |
| Component |
|---|
| Rotary dryer |
| Tube ball mill |
| Classifier |
| Airlock valve |
| Two-chamber ball mill |
| Slurry pump |
| Dosing pump |
| Wet Ball mill |
| Settling tank |
| Contact tank |
| Gypsum calcining kettle |
| Grinding mill |
Models with the same components are grouped together; select a group to open its component table.
| No. | Component | Location |
|---|---|---|
| 1 | Baghouse dust collector | Flue gas cleaning section |
| 3 | Bucket elevator | Finished product vertical conveying section |
| 4 | Silo | Finished product storage section |
| 5 | Cyclone dust collector | Process pre-dedusting position |
| Model-specific component | ||
| Two-compartment ball mill | Raw material grinding section | |
| Classifier | Classification section after grinding |
| Component | Location |
|---|---|
| Slurry pump | |
| Metering pump | |
| Wet Ball mill | Lime wet grinding section |
| Settling tank | Slurry impurity separation section after grinding |
| Liquid preparation tank | Lime milk storage and preparation section |
| No. | Component | Location |
|---|---|---|
| 1 | Baghouse dust collector | Flue gas cleaning section |
| 2 | Ball mill | Raw material grinding section |
| 3 | Bucket elevator | Finished product vertical conveying section |
| 4 | Silo | Finished product storage section |
| Rotary dryer | Heat treatment drying section |
| No. | Component | Location |
|---|---|---|
| 1 | Baghouse dust collector | Flue gas cleaning section |
| 2 | Ball mill | Raw material grinding section |
| 3 | Bucket elevator | Finished product vertical conveying section |
| 4 | Silo | Finished product storage section |
| No. | Component | Location |
|---|---|---|
| 6 | Conveyor belt | |
| Gypsum calcining kettle | Gypsum heat treatment section after grinding | |
| Grinding mill | Gypsum raw material grinding and drying section |
| No. | Component | Location |
|---|---|---|
| 1 | Baghouse dust collector | Flue gas cleaning section |
| 6 | Conveyor belt | |
| Rotary dryer | Heat treatment drying section |
| Component | Location |
|---|---|
| Tube ball mill | Combined grinding position |
| Classifier | Classification section after grinding |
The Mineral-powder Processing Lines covers 7 models: Strommashina model, Strommashina model, Strommashina model, /, 2–5 μm, МП / СТРОМ-МИН, ВНВ. Former and renamed designations are listed in the models table on this page.
The Mineral-powder Processing Lines is also documented under these designations: Strommashina model, 2013 20 t / h, 2013 15 t / h, /, 2–5 μm, 2013 5 t / h, МП / СТРОМ-МИН, МП-1, МП-2, СТРОМ-МИН-8, СТРОМ-МИН-15, СТРОМ-МИН-30, ВНВ.
The Mineral-powder Processing Lines is listed under the Strommashina brand. Period: 2013. Status: Historical model.
18 components are recorded, including: Conveyor belt, Slurry pump, Metering pump, Gypsum calcining kettle, Grinding mill, Rotary dryer, Baghouse dust collector, Ball mill and more. The full list with locations is in the components table on this page.
Model-specific components with their own page: Gypsum calcining kettle, Grinding mill, Rotary dryer, Baghouse dust collector, Ball mill, Bucket elevator, Silo, Wet Ball mill and more (14 in total).
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry