Mining hydraulic excavator · 1987 · 20 models
Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Bucket | End of the front working attachment | EX1200-7 |
| 2 | Boom | Between the upper structure and the arm | EX1200-7 |
| 3 | Arm / stick | Between the boom and the bucket | EX1200-7 |
| 4 | Boom cylinder | Between the front upper structure and the boom base | EX1200-7 |
| 5 | Arm cylinder | Above the boom, actuating the arm | EX1200-7 |
| 6 | Bucket cylinder | On the arm, actuating the bucket linkage | EX1200-7 |
| 7 | Cab | Operator cab on the upper structure | EX1200-7 |
| 8 | Undercarriage assembly | Travel undercarriage below the upper structure | EX1200-7 |
| Component |
|---|
| Bucket tooth / tip |
| Bucket tooth adapter |
| Bucket cutting edge |
| Bucket wear plate |
| Lip shroud |
| Wing shroud |
| Adapter wear cap |
| Main hydraulic pump |
| Swing motor |
| Track shoe |
| Slewing bearing |
Models with the same components are grouped together; select a group to open its component table.
Models: EX2000-7, EX2600-7, EX3600-7, EX8000-7
| No. | Component | Location |
|---|---|---|
| 1 | Bucket | Work equipment end, connected to the arm or loader linkage |
| 2 | Boom | Between the excavator slewing platform and the arm |
| 3 | Bucket rod | Between the excavator boom tip and the bucket |
| 7 | Cab | Operator seating and control area |
| 8 | Undercarriage assembly | Underside of the crawler excavator |
| Bucket Tooth / Tip | ||
| Tooth adapter | ||
| Model-specific component | Front edge of the bucket | |
| Model-specific component | ||
| Model-specific component | ||
| Model-specific component | ||
| Model-specific component | ||
| Main hydraulic Pump | Hydraulic power system | |
| Swing motor | Excavator slewing drive system | |
| Track shoe | Outer ground-contact travel surface of the track chain | |
| Slewing bearing | Between the excavator slewing platform and the undercarriage |
Models: EX5600-7, EX5600-7P
| No. | Component | Location |
|---|---|---|
| 1 | Bucket | Work equipment end, connected to the arm or loader linkage |
| 2 | Boom | Between the excavator slewing platform and the arm |
| 3 | Bucket rod | Between the excavator boom tip and the bucket |
| 7 | Cab | Operator seating and control area |
| 8 | Undercarriage assembly | Underside of the crawler excavator |
| Bucket Tooth / Tip | ||
| Tooth adapter | ||
| Model-specific component | Front edge of the bucket | |
| Model-specific component | ||
| Model-specific component | ||
| Model-specific component | ||
| Model-specific component | ||
| Main hydraulic Pump | Hydraulic power system | |
| Track shoe | Outer ground-contact travel surface of the track chain | |
| Slewing bearing | Between the excavator slewing platform and the undercarriage |
| No. | Component | Location |
|---|---|---|
| 1 | Bucket | Work equipment end, connected to the arm or loader linkage |
| 2 | Boom | Between the excavator slewing platform and the arm |
| 3 | Bucket rod | Between the excavator boom tip and the bucket |
| 7 | Cab | Operator seating and control area |
| 8 | Undercarriage assembly | Underside of the crawler excavator |
| Bucket Tooth / Tip | ||
| Tooth adapter | ||
| Model-specific component | Front edge of the bucket | |
| Model-specific component | ||
| Model-specific component | ||
| Model-specific component | ||
| Model-specific component | ||
| Main hydraulic Pump | Hydraulic power system | |
| Swing motor | Excavator slewing drive system | |
| Track shoe | Outer ground-contact travel surface of the track chain |
The Mining hydraulic excavator covers 20 models: EX mini series, EX1200-5, EX1200-7, EX1800, EX1900-5, EX200-5X, EX2000-7, EX225USR-5, EX2500-5, EX2600-7, EX3500-3, EX3500, EX3600-5, EX3600-7, EX5500-5, EX5500, EX5600-7, EX5600-7P, EX8000-7, EX8000. Former and renamed designations are listed in the models table on this page.
The Mining hydraulic excavator is also documented under these designations: EX mini series, EX1200-5, EX1200-7, EX1800, EX1900-5, EX200-5X, EX2000-7, EX225USR-5, EX2500-5, EX2600-7, EX3500-3, EX3500, EX3600-5, EX3600-7.
The Mining hydraulic excavator is listed under the Hitachi Construction Machinery brand as: Mining hydraulic excavator. Period: 1987. Status: Historical model.
16 components are recorded, including: Bucket Tooth / Tip, Tooth adapter, Undercarriage assembly, Bucket, Boom, Bucket rod, Cab, Main hydraulic Pump and more. The full list with locations is in the components table on this page.
Model-specific components with their own page: Undercarriage assembly, Bucket, Boom, Bucket rod, Cab, Main hydraulic Pump, Swing motor, Track shoe and more (9 in total).
Send us a drawing or sample and tell us the equipment model and part name.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Or contact us directly: +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to the customer technical requirements, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
We review mating surfaces and interface dimensions and assess material, heat treatment and manufacturing feasibility.
Material grades and heat-treatment processes are specified order by order, stated in the technical agreement and tracked through production.
Drawing confirmation, material and process control, production tracking, inspection and acceptance coordination.
We coordinate manufacturing, quality confirmation, packaging and delivery of complete finished parts in a workable, closed-loop supply process.
Provide the existing model, drawings, drawing, materials or operating conditions so we can identify the appropriate technical review and supply route.
Submit an Enquiry