METSO · Détails de la pièce

Eccentric Bushing

Eccentric Bushing

Identify parts for Metso cone crushers, check models and drawing, confirm materials and processes, and submit an inquiry.

Équipements et modèles applicables

Identifiez le modèle installé et les dimensions clés, puis vérifiez la révision du plan et les interfaces physiques.

Equipment Series

Metso Cone Crushers

Models and Key Dimensions

Metso HP series (HP100-HP800), GP series (GP100-GP550), and MP series (MP800-MP1000)

Matériaux et procédés

Select the material grade and heat treatment for the operating conditions, processed material and equipment specifications. The options below are commonly used; confirm the final grade against the drawing and technical agreement.

C95400 aluminum bronze (ASTM B148)

Candidate aluminum bronze; verify casting and heat treatment condition, composition and mechanical properties against the eccentric bushing drawing and material standard.

Aluminum bronze C95500 (ASTM B148)

Candidate nickel-aluminum bronze; confirm suitability for heavy loading and mechanical properties for the specified material condition and part drawing.

C93200 leaded tin bronze (SAE 660)

Candidate leaded bearing copper alloy; select for the load, speed and lubrication conditions. The material cannot replace the lubrication required by the equipment.

Caractéristiques d'usure et remplacement

Modes d'usure et conseils d'entretien courants ; le cycle réel dépend des conditions, du matériau et des données de fonctionnement.

Modes d'usure courants

  • Eccentric mainshaft loading causes uneven bushing bore wear, concentrated in the direction of eccentric loading
  • Inadequate lubrication causes bushing scuffing and seizure; severe cases can weld the bushing to the mainshaft
  • Foreign particles in the lubricant cause axial grooves in the bushing surface
  • Fretting between the bushing outside diameter and housing bore loosens the fit
Critères de remplacement

Check bushing wear and fitting clearance against the maintenance manual. Stop and inspect if the stroke becomes abnormal, copper debris keeps increasing, or surfaces show seizure or scoring. Base replacement on actual damage and model-specific limits. Control interference between the outside diameter and housing bore to the drawing.

Contrôle matière et procédé

Les exigences matière, traitement thermique, procédés composites et contrôles suivent le plan, les conditions et le contrôle technique.

Material Grade / Substrate

The material grade and applicable standard must follow the drawing or confirmed technical specification for the machine model. Candidate materials on this page are not an OEM grade designation.

Heat Treatment Condition

Select the heat treatment condition for the specific copper alloy grade and part drawing; verify final hardness and microstructure against the technical agreement.

Composite / Hardfacing Requirements

Bronze bushings are not suitable for weld overlay repair. Replace the worn bushing as a complete part; surface repair is not recommended.

Dimensions and Inspection

Manufacture to drawings produced from part measurements or supplied by the customer. Critical mating surface tolerances follow OEM requirements. Specify nondestructive testing methods suitable for the material and part geometry. Agree the inspection scope and acceptance criteria in the technical specification.

Des pièces de même nom peuvent ne pas être interchangeables selon le modèle, la révision du plan, les interfaces et les exigences matière. Avant fabrication, se baser sur le modèle complet, le numéro de série et les plans.

Send Your Wear Part Requirements

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry