METSO · Détails de la pièce

Arm Guard

Arm Guard / Arm Liner

Identify parts for Metso cone crushers, check models and drawing, confirm materials and processes, and submit an inquiry.

Équipements et modèles applicables

Identifiez le modèle installé et les dimensions clés, puis vérifiez la révision du plan et les interfaces physiques.

Equipment Series

Metso Cone Crushers

Models and Key Dimensions

Metso HP series (HP100-HP800), GP series (GP100-GP550), and MP series (MP800-MP1000)

Matériaux et procédés

Select the material grade and heat treatment for the operating conditions, processed material and equipment specifications. The options below are commonly used; confirm the final grade against the drawing and technical agreement.

High-Manganese Steel Mn13Cr2

Solution-treated, water-quenched high-manganese wear steel; the degree of work hardening depends on impact loading and actual operating conditions.

High-Manganese Steel Mn18Cr2

A high-manganese steel option; compare it with Mn13Cr2 using impact severity, material abrasiveness and actual wear records.

Hardox 400 Wear-Resistant Steel Plate

For low-to-moderate impact and high sliding wear; verify hardness against the specific grade, thickness and material certificate.

Metso XT710

Specify independently manufactured replacement materials through the agreed specification, heat certificate and test results. Where an OEM commercial material is cited for identification, label it as an original-part reference and confirm ANRANST supply material separately without assuming equivalence or a life multiplier.

Caractéristiques d'usure et remplacement

Modes d'usure et conseils d'entretien courants ; le cycle réel dépend des conditions, du matériau et des données de fonctionnement.

Modes d'usure courants

  • Material impact causes surface dents and plastic deformation.
  • Sliding material causes grooves and localized thinning.
  • Progressive wear exposes the metal structure of the arm; replace the liner before structural damage occurs.
  • Wear enlarges the mounting bolt holes and loosens the fastening.
Critères de remplacement

Assess replacement against the arm guard remaining-thickness limit in the drawing. Replace if through-cracks, extensive spalling or bolt hole wear causing fastening failure occurs.

Contrôle matière et procédé

Les exigences matière, traitement thermique, procédés composites et contrôles suivent le plan, les conditions et le contrôle technique.

Material Grade / Substrate

Mn13Cr2 and Mn18Cr2 high-manganese steels, Hardox 400 wear plate, and other specified materials

Heat Treatment Condition

Solution heat treatment with water quenching. Final hardness and microstructure must meet the drawing and agreed technical specification.

Composite / Hardfacing Requirements

Weld Hardox wear plate using an approved procedure for the grade and thickness. Select consumables, preheat, interpass temperature and repair limits in accordance with the manufacturer's recommendations and the drawing.

Dimensions and Inspection

Manufacture to drawings produced from part measurements or supplied by the customer. Critical mating surface tolerances follow OEM requirements. Use UT/MT inspection to assess castings for shrinkage porosity and cracks against the agreed acceptance criteria.

Des pièces de même nom peuvent ne pas être interchangeables selon le modèle, la révision du plan, les interfaces et les exigences matière. Avant fabrication, se baser sur le modèle complet, le numéro de série et les plans.

Send Your Wear Part Requirements

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry