Sugar Cane Mill

Sugar cane mills commonly use a tandem of three-roll milling units. The top roll and two lower rolls compress the prepared cane, while the trash plate guides the bagasse and roll-end gears synchronize rotation. Wear is concentrated on roll shells, roll teeth, trash plates, bearing bushes and bagasse passages.

Sugar cane mill

Equipment Section View

Sugar Cane Mill
Sugar cane mill section view showing component positions

Sugar cane mills commonly use a tandem of three-roll milling units. The top roll and two lower rolls compress the prepared cane, while the trash plate guides the bagasse and roll-end gears synchronize rotation. Wear is concentrated on roll shells, roll teeth, trash plates, bearing bushes and bagasse passages.

Equipment Parts

Part Identification and Technical Details

Explore part names, images, material options and technical requirements. Select a card to open the corresponding replacement part page.

Individual parts

Pièces unitaires et de maintenance

Roll Shell
01

Roll Shell

Alloy ductile iron, nickel-chromium-molybdenum alloy cast iron or cast steel substrate

Technical Requirements
Working layer ; balance compressive strength, resistance to thermal cracking and a secure fit on the roll shaft. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Roll Teeth
02

Roll Teeth

Same base material as the roll shell; tooth tips may use Fe-Cr-C hardfacing or welded carbide inserts

Technical Requirements
Hardfacing ; measure the tooth profile and groove helix angle from the original roll. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Trash Plate
03

Trash Plate

Cr20–Cr28 high-chromium white iron, wear-resistant alloy cast steel or composite plate

Technical Requirements
Working surface. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Bearing Bush
04

Bearing Bush

Tin bronze, aluminum bronze or steel-backed Babbitt alloy

Technical Requirements
Bronze. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Mill Pinion
05

Mill Pinion

42CrMo, 18CrNiMo7-6 carburizing steel or quenched and tempered alloy steel

Technical Requirements
Tooth surface; tough core. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Mill Crown Wheel
06

Mill Crown Wheel

ZG35CrMo, 42CrMo or high-strength cast steel

Technical Requirements
large gears. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Top Roll Cap
07

Top Roll Cap

ZG270-500 cast steel or high-strength low-alloy steel

Technical Requirements
non-destructive testing of pin bores, load-bearing fillets and welds. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Bottom Rail
08

Bottom Rail

42CrMo, wear-resistant low-alloy steel or surface-hardened steel

Technical Requirements
guide surfaces; control flatness and parallelism of the guide surfaces. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Feed roll and feed plate
09

Feed Roll / Feed Plate

Alloy cast iron or NM400/NM450, with hardfacing where required

Technical Requirements
Working surface. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.
Juice Box Liner
10

Juice Box Liner

304L / 316L stainless steel or food-grade rubber

Technical Requirements
316L is suited to chloride-containing cleaning environments; welds should be smooth and easy to clean, without pockets that retain liquid
Bagasse Chute Liner
11

Bagasse Chute Liner

NM400, UHMW-PE, rubber or stainless steel

Technical Requirements
Wear-resistant steel. Confirm hardness, tensile strength and other numerical properties against a material specification, manufacturer data or approved project record before publishing.

Materials for similarly named parts may differ by OEM, machine model and operating conditions. Confirm the machine model, drawing and measured dimensions before ordering or manufacture.

Materials for similarly named parts may differ by OEM, machine model and operating conditions. Confirm the machine model, drawing and measured dimensions before ordering or manufacture.

Discuss Your Sugar Cane Mill Wear Parts

Provide the machine model, operating conditions and target service life so our engineers can recommend materials and prepare a quotation.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry