Marcy Rod Mill (Open End/EPD/CPD)

Rod mill · 1925 · 1 model

Marcy Rod Mill (Open End/EPD/CPD) – Rod mill
Marcy Rod Mill (Open End/EPD/CPD) – Rod mill (2)
Marcy
MarcyBrand
Rod millEquipment type
1925Period
Historical modelStatus
Marcy

Models and Historical Names in This Series

Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.

ModelHistorical names / renamingsPeriodComponents
Marcy Rod Mill (Open End/EPD/CPD)Marcy Open End Rod Mill; Marcy Open End Rod mill 6×12; Marcy End Peripheral Discharge Rod Mill (EPD); Marcy Center Peripheral Discharge Rod Mill (CPD); Marcy Rod Mill 9×12; Marcy Rod mill 6¼ ft × 12½ ft; Marcy 15 ft; Marcy; Marcy rod mill 4×10ft; Marcy Open End Rod Mill 2ft×4ft; Marcy Rod Mill 5 x 12 L.H. Direct Driven S+D192517
Marcy

Numbered Components

The numbers on the diagram correspond one to one with the rows below.

No.ComponentLocationApplies to
1Rod mill shellOuter cylindrical shell of the foreground mill
2Rod mill headRight-hand head of the foreground mill
Marcy

Components by Model

Models with the same components are grouped together; select a group to open its component table.

Marcy Rod Mill (Open End/EPD/CPD)17 items
ComponentLocation
Shell Liner / Shell Plate — Tube inner liner (1938 site)Inside the grinding shell; the original text is lined throughout, the end split is not listed
Grinding Rods / Steel Rods — Grinding rod (1938 site)Inside the grinding shell
Shell Liner / Shell Plate — Single wave shell liner (Lakefield test)The inner wall of the cylinder; six pieces, each piece is 25mm thick, and the central single wave is about 25mm high
Grinding Rods / Steel Rods — Grinding rod (Lakefield test)Inside the grinding shell, original diameter 12 to 76mm
Transmission motor (Lakefield test)Rod mill external drive, 7.5hp
Pulley and V-belt (Lakefield test)Motor to gear transmission
Pinion (Lakefield test)gear meshing transmission
girth gear (Lakefield test)Mill external drive
Grand Junction single scoop feeder2×4ft rod mill feeding section; scoop radius 21in
Grand Junction Rod Mill EndBoth ends of the cylinder are connected to the hollow shaft support
Grand Junction Rod Mill Hollow ShaftSupport at both ends of cylinder
Grand Junction hollow shaft bearingHollow shaft support at both ends
Grand Junction spur gearRod mill drive; number of teeth/interface not specified
Grand Junction drive pinionDrive matched with spur gear
Shell Liner / Shell Plate — Grand Junction shell linerInner wall of rod mill shell
Head Liner / End Liner — Grand Junction end linerInternal surface of rod mill end
Grand Junction liner boltFixed rod mill liner; hole-by-hole position not specified

Frequently asked questions

What other names or designations is the Marcy Rod Mill (Open End/EPD/CPD) known by?

The Marcy Rod Mill (Open End/EPD/CPD) is also documented under these designations: Marcy Rod Mill, Marcy Open End Rod Mill, Marcy Open End Rod mill 6×12, Marcy End Peripheral Discharge Rod Mill, Marcy Center Peripheral Discharge Rod Mill, Marcy Rod Mill 9×12, Marcy Rod mill 6¼ ft × 12½ ft, Marcy 15 ft, Marcy, Marcy rod mill 4×10ft, Marcy Open End Rod Mill 2ft×4ft, Marcy Rod Mill 5 x 12 L.H. Direct Driven S+D.

Which brand and type of equipment is the Marcy Rod Mill (Open End/EPD/CPD)?

The Marcy Rod Mill (Open End/EPD/CPD) is listed under the Marcy brand as: Rod mill. Period: 1925. Status: Historical model.

Which components and wear parts are recorded for the Marcy Rod Mill (Open End/EPD/CPD)?

17 components are recorded, including: Shell Liner / Shell Plate, Grinding Rods / Steel Rods, Shell Liner / Shell Plate, Grinding Rods / Steel Rods, Transmission motor (Lakefield test), Pulley and V-belt (Lakefield test), Pinion (Lakefield test), girth gear (Lakefield test) and more. The full list with locations is in the components table on this page.

How do I enquire about parts for the Marcy Rod Mill (Open End/EPD/CPD)?

Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.

Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry