Marcy ball mill

Ball mill · 1917 · 1 model

Marcy ball mill – Ball mill
Marcy ball mill – Ball mill (2)
Marcy
MarcyBrand
Ball millEquipment type
1917Period
Historical modelStatus
Marcy

Models and Historical Names in This Series

Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.

ModelHistorical names / renamingsPeriodComponents
Marcy ball millMarcy Ball mill 8; Marcy Ball mill 10 6 ×17; Marcy Ball mill 13 6 ×15; Marcy Ball mill No.66; Marcy Ball mill No.67; Marcy Ball mill No.86; Marcy Ball mill 9ft6in × 12ft; Marcy mill; Marcy ball mill 24in×18in191718
Marcy

Numbered Components

The numbers on the diagram correspond one to one with the rows below.

No.ComponentLocationApplies to
1Grinding ballsGrinding ballsSteel-ball charge exposed in the cutaway
1Mill shellOuter wall of the rotating shell
2Mill trunnionHollow shaft at the left end adjoining the front support
2Manhole coverInspection opening cover on top of the shell
3Mill shellOuter cylindrical shell of the rotating mill
3Girth gearDrive gear around the right-hand shell circumference
4Trunnion bearing housingSupport housing around the left-hand trunnion
4Steel linersLining layer on the inner shell wall
5Synchronous motor250hp GE synchronous motor at the rear right
5Mill trunnionHollow support trunnion outside the mill head
6Brake wheelBrake wheel at the upper far right
6Feed inletInlet at the left-hand hollow trunnion
7Drive shaftExposed shaft between the motor and the right-hand mill end
7Discharge coneConical discharge area between the grate and right-hand trunnion
8Steel discharge grateVertical grate at the right-hand end of the grinding chamber
9Product outletProduct outlet outside the right-hand hollow trunnion
Marcy

Components by Model

Models with the same components are grouped together; select a group to open its component table.

Marcy ball mill18 items
No.ComponentLocation
1Grinding Balls / Steel BallsInside the grinding shell
1Mill shellRotary grinding body
2Mill trunnionSupport at both ends of grinding shell
2Manhole covershell maintenance opening
3Girth gearExternal drive side of grinding shell
4Steel linerinner wall of cylinder
6The 7th edition picture feed portFigure 20-31 The hollow shaft entrance at the left end; the functional interface shown in the figure does not mean that it has been certified as an independent supply part
77th edition picture provided for discharging coneFigure 20-31 From behind the discharge grate plate at the right end to the hollow shaft
8Steel discharge grateDischarging end
Ball access coverNo.86 cylinder oval opening
Mill shellRotary grinding drum
Discharging drum screenLucky Friday site 9ft6in×12ft mill discharge end
ReducerLucky Friday on-site ball mill driver
Mill motorLucky Friday field driver
High pressure and low pressure lubrication systemLucky Friday on-site mill support lubrication
Open gear lubrication deviceLucky Friday on-site transmission lubrication
Entry Marcy vertical grid partitionNear the discharge end
Entry Marcy Discharging and Grading ScreenBetween the grid partition and the cylinder end; not the grate plate itself

Frequently asked questions

What other names or designations is the Marcy ball mill known by?

The Marcy ball mill is also documented under these designations: Marcy Ball mill 8, Marcy Ball mill 10 6 ×17, Marcy Ball mill 13 6 ×15, Marcy Ball mill No.66, Marcy Ball mill No.67, Marcy Ball mill No.86, Marcy Ball mill 9ft6in × 12ft, Marcy mill, Marcy ball mill 24in×18in.

Which brand and type of equipment is the Marcy ball mill?

The Marcy ball mill is listed under the Marcy brand as: Ball mill. Period: 1917. Status: Historical model.

Which components and wear parts are recorded for the Marcy ball mill?

18 components are recorded, including: Grinding Balls / Steel Balls, Mill trunnion, Mill shell, Ball access cover, Mill shell, Steel liner, Steel discharge grate, Girth gear and more. The full list with locations is in the components table on this page.

How do I enquire about parts for the Marcy ball mill?

Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.

Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce

Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.

Demander un devis

Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com

Manufacturing Services in China

From Technical Assessment to Finished-Part Delivery

ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.

Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.

Submit an Enquiry