What other names or designations is the Boliden Allis rotary kiln known by?
The Boliden Allis rotary kiln is also documented under these designations: Rotary kiln radial.
Rotary kiln · 1988–1989 · 1 model


Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Boliden Allis rotary kiln | Rotary kiln radial | 1988–1989 | 33 |
Models with the same components are grouped together; select a group to open its component table.
| Component | Location |
|---|---|
| Kiln Inlet / Outlet Seal — Flexible blade kiln end seal | Static/dynamic interface at the end of the rotary kiln |
| Flexible main blade seal | Kiln end and stationary cover interface; examples and claims |
| Staggered seam covering fiber blanket | Main blade side cover gap |
| Second set of bias blades (optional) | Blade and carpet interlayer, some embodiments may not be provided |
| Removable bracket, flange and fastener (grouped components) | Fixed cover wall or hoop with blades/blanket |
| Drum housing | Example rotating cylinder |
| shell refractory lining | Example barrel |
| Kiln Tyre / Riding Ring — Kiln tyre / riding ring | Example barrel outer circumference |
| Support Roller / Carrying Roller — Support roller | Example support riding ring |
| Feeding cover and feeding chute | Example of high-end feeding stationary cover/chute |
| Inlet end plate and annular ferrule | The annular gap is formed by the rotating end plate/stationary ferrule at the feed end |
| Discharge end plate | Discharge port at the lower end of the drum |
| Combustion end cover and refractory lining | Example discharge side combustion cover |
| Burner (Example) | Inside the combustion end cover, conventional burner |
| Radial bearing seat and end cover | Support roller shaft seat and bolt end cover |
| Radial aligning insert | Swing insert on the curved support of the bearing seat |
| Radial bearing/lining | Approximately 180° between the supporting roller shaft and the radial insert is a preferred example |
| Axial thrust wear plate | End of supporting roller shaft, thrust bearing surface |
| Thrust support plate | Behind thrust wear plate |
| Axial alignment components (two components grouped) | Thrust plate rear curved surface/planar matching component |
| Axial/radial stop lug (grouped components) | Anti-rotation of lining and support plate or axial movement of insert |
| Centering key and installation lever | Key mates with housing/radial insert; mounting lever for center adjustment |
| Anti-movement fastener (grouped components) | Anti-axial movement of lining; dimensions not specified |
| Cooling serpentine coil | Near the radial bearing bush, water/ethylene glycol or suitable cooling fluid |
| High-pressure oil supply pipeline and connector (optional) | End cover, support plate, hollow screw and thrust ring groove passage |
| High pressure flexible hose (optional) | Oil supply circuit allows relative movement of components |
| Oil scoop | The oil storage chamber provides low-pressure oil to the radial bearing bush |
| Oil storage chamber and oil channel (grouped components) | Interconnected oil storage chamber for oil distribution |
| Shaft oil seal | Prevent excessive leakage between shaft and bearing seat |
| Lubrication disc | Measuring oil dripping onto the shaft |
| Thrust member retainer | Axial support fixed |
| Axis measuring hole/measuring rod interface | Four-direction holes are the preferred example for installation and centering purposes. |
| Proximity sensor (optional) | Original capacitive/ultrasonic proximity detection option, not standard for all commercial kilns |
The Boliden Allis rotary kiln is also documented under these designations: Rotary kiln radial.
The Boliden Allis rotary kiln is listed under the Boliden Allis brand as: Rotary kiln. Period: 1988–1989. Status: Historical model.
33 components are recorded, including: Kiln Inlet / Outlet Seal, Flexible main blade seal, Staggered seam covering fiber blanket, Second set of bias blades (optional), Removable bracket, flange and fastener (grouped components), Drum housing, shell refractory lining, Kiln Tyre / Riding Ring and more. The full list with locations is in the components table on this page.
Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.
Submit an Enquiry