What other names or designations is the Bergeaud ATV vibrating scalping screen feeder known by?
The Bergeaud ATV vibrating scalping screen feeder is also documented under these designations: Bergeaud ATV1050, Metso Bergeaud ATV10-50.
Vibrating scalping feeder · 1978-07 · 1 model


Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Bergeaud ATV vibrating scalping screen feeder | Bergeaud ATV1050; Metso Bergeaud ATV10-50 | 1978-07 | 24 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Vibrating body | Feeder trough at the front of the photograph | |
| 2 | ATV10-50 rubber springs (HMV stock) | Resilient supports below the feeder trough | |
| 3 | Grizzly fingers | Grizzly section towards the rear of the feeder trough |
| Component |
|---|
| ATV1050 (1978) grooved plate |
| ATV1050 (1978) double counterweight mechanism |
| ATV1050 (1978) support spring |
| ATV1050 (1978) heavy duty hopper |
| ATV dual-axis version of the excitation shaft |
| ATV double-axis version spherical roller bearing |
| ATV dual-shaft version synchronization gear |
| ATV dual-axis version drive motor |
| ATV biaxial version first layer cut grille with different openings |
| ATV dual-axis version second layer vibrating rod |
| ATV dual-axis speed control device category (option) |
| ATV electric vibration version electric vibration motor |
| ATV electric vibrating chain curtain |
| ATV electric vibrating version hopper |
| ATV electric vibrating version of the column |
| ATV electric vibration version frame |
| ATV electric vibration version suspension rod |
| ATV electric vibration version vibration body |
| ATV electric vibrating version of the first layer cut grille |
| ATV electric vibrating version second layer vibrating rod |
| ATV electric vibration version speed regulating device category (option) |
| ATV10-50 first section grille finger (HMV stock) |
| ATV10-50 second section grille finger (HMV stock) |
Models with the same components are grouped together; select a group to open its component table.
| No. | Component | Location |
|---|---|---|
| 2 | ATV10-50 rubber spring (HMV stock) | 6 pieces, outer diameter 180mm and height 150mm; manufacturer standard/spare parts set quantity unknown |
| ATV1050 (1978) grooved plate | troughing plate | |
| ATV1050 (1978) double counterweight mechanism | double counterweight mechanism, non-reverse precision bearing/gear | |
| ATV1050 (1978) support spring | Institutional support | |
| ATV1050 (1978) heavy duty hopper | Located in front of the feeding equipment | |
| ATV dual-axis version of the excitation shaft | two | |
| ATV double-axis version spherical roller bearing | four | |
| ATV dual-shaft version synchronization gear | Original text 1 gear, no number of teeth/material | |
| ATV dual-axis version drive motor | One unit | |
| ATV biaxial version first layer cut grille with different openings | two pieces | |
| ATV dual-axis version second layer vibrating rod | This paragraph is clear | |
| ATV dual-axis speed control device category (option) | Original SPEED VARIATION, the specific controller is not documented | |
| ATV electric vibration version electric vibration motor | Two units, 35° to 45° linear vibration | |
| ATV electric vibrating chain curtain | CHAIN CURTAIN | |
| ATV electric vibrating version hopper | HOPPER | |
| ATV electric vibrating version of the column | POST | |
| ATV electric vibration version frame | FRAME | |
| ATV electric vibration version suspension rod | SUSPENSION STUDS | |
| ATV electric vibration version vibration body | VIBRATING BODY | |
| ATV electric vibrating version of the first layer cut grille | Two pieces of divergent opening | |
| ATV electric vibrating version second layer vibrating rod | This paragraph is clear | |
| ATV electric vibration version speed regulating device category (option) | original watch SPEED VARIATION | |
| ATV10-50 first section grille finger (HMV stock) | 1300mm long × 1000mm wide, not the old full series size | |
| ATV10-50 second section grille finger (HMV stock) | 1000mm long×1000mm wide |
The Bergeaud ATV vibrating scalping screen feeder is also documented under these designations: Bergeaud ATV1050, Metso Bergeaud ATV10-50.
The Bergeaud ATV vibrating scalping screen feeder is listed under the Bergeaud brand as: Vibrating scalping feeder. Period: 1978-07. Status: Historical model.
24 components are recorded, including: ATV1050 (1978) grooved plate, ATV1050 (1978) double counterweight mechanism, ATV1050 (1978) support spring, ATV1050 (1978) heavy duty hopper, ATV dual-axis version of the excitation shaft, ATV double-axis version spherical roller bearing, ATV dual-shaft version synchronization gear, ATV dual-axis version drive motor and more. The full list with locations is in the components table on this page.
Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.
Submit an Enquiry