Installed mill record
Send the nameplate, project reference, full model, serial number, shell size, drive arrangement and discharge configuration.
A drawing-based route for identifying parts for installed NKMZ MMPS wet semi-autogenous mills. Final manufacture is confirmed against the project equipment and submitted part information.
The local NKMZ brand dossier records the MMPS-7750×6060 series designation. Confirm the full nameplate, serial number, shell dimensions, drive and discharge arrangement, drawing or part reference, installed position and current-part photographs for the actual project.
Send the nameplate, project reference, full model, serial number, shell size, drive arrangement and discharge configuration.
Identify the feed, shell, head or discharge position; confirm orientation, interfaces, fixing pattern and adjacent components.
Use the drawing revision, key dimensions, current-part photographs, wear observations and acceptance requirements for technical review.
These names identify installation positions only. Geometry, drilling, material and supply scope are reviewed against the submitted mill and drawing; they are not inferred from the MMPS series name.
Confirm throat or feed-end location, segment boundaries, holes, orientation, feeder interfaces and measured dimensions.
Confirm the liner layout, lifter profile, pitch, fixing pattern, shell diameter, handedness and adjacent segments.
Confirm grates, pulp-lifting or transition positions, openings, flow passages, interfaces, orientation and wear or blockage records.
For gears, pinions or structural parts, use the drawing and interfaces to check the specific part. Do not infer a matched set from a general model reference.
The local source set does not contain a public, project-by-project MMPS spare-parts directory. OEM and third-party references remain separate and each must be confirmed against the supplied equipment and drawing evidence.
No. A project record and part position are required because fit depends on the actual configuration, interfaces and drawing revision.
No. The installed position, geometry, interfaces, fixing pattern, duty, wear mechanism and acceptance requirements are part of the review.
Send the nameplate, mill dimensions, general arrangement, installed position, current-part photographs, liner layout and measured key dimensions. The remaining unknown fields can then be identified before manufacture.
Include the full model, serial number, mill dimensions, installed position, drawing or part reference, current-part photographs, liner layout and operating observations. We will define the identification and supply route from the submitted evidence.
اتصال مباشر: +86 156 3797 3199
zzx@anranst.com
توفر شركة ANRANST للعملاء العالميين تقييمات هندسية، واختيار التصنيع الصيني، ومراقبة الجودة، وتسليم الأجزاء النهائية لقطع الغيار الصناعية المقاومة للتآكل حسب الطلب، ويمكنها أيضًا دعم قطع الغيار الصناعية الأخرى حسب الطلب.
قم بمراجعة أسطح التزاوج وأبعاد الواجهة، وقم بتقييم جدوى المواد والمعالجة الحرارية والتصنيع.
تُحدَّد درجات المواد وعمليات المعالجة الحرارية لكل طلب على حدة، وتُثبَّت في الاتفاقية الفنية وتُتابَع أثناء الإنتاج.
يشمل ذلك تأكيد الرسم، ومراقبة المواد والعمليات، وتتبع الإنتاج، وتنسيق عمليات الفحص والقبول.
تنظيم عمليات التصنيع والتحقق من الجودة والتعبئة والتغليف وتسليم المنتجات النهائية الكاملة لتشكيل حلقة إمداد قابلة للتنفيذ.
قم بتزويدنا بالنماذج الحالية، والرسومات، وأرقام الرسومات، وأرقام الأجزاء، والمواد، أو معلومات ظروف التشغيل، وسنقوم بتحديد التحقق الفني ومسار التوريد وفقًا لذلك.
إرسال طلب