Which models does the EnduraHog Chip-Sizer CS cover?
The EnduraHog Chip-Sizer CS covers 4 models: 30CS, 34CS, 45CS, 56CS. Former and renamed designations are listed in the models table on this page.
2026 · 4 models


The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to | |
|---|---|---|---|---|
| 1 | Breaker plate | Breaker plate on the left side of the housing cutaway | EnduraHog Chip-Sizer CS | |
| 2 | Screen grate | Curved screen grate beneath the rotor | EnduraHog Chip-Sizer CS | |
| 3 | Housing liner | Rear housing liner in the inlet area | EnduraHog Chip-Sizer CS | |
| 4 | ![]() | Rotor assembly | Series-specific rotor in the lower component image | EnduraHog Chip-Sizer CS |
| 5 | Hammer | Working hammer at the outer rotor perimeter | EnduraHog Chip-Sizer CS | |
| 6 | Rotor disc | Front end disc of the series-specific rotor | EnduraHog Chip-Sizer CS | |
| 7 | Rotor shaft | Rotor shaft projecting at the lower left | EnduraHog Chip-Sizer CS |
| Component |
|---|
| Hammer Axle / Hammer Pin |
| Hammer-pin retainer |
Models with the same components are grouped together; select a group to open its component table.
Models: 30CS, 34CS, 45CS, 56CS
| No. | Component | Location |
|---|---|---|
| 1 | Impact Plate / Breaker Plate | |
| 2 | Grate Bar | |
| 3 | Side Housing Liner | |
| 5 | Hammer / Swing Hammer | |
| 6 | Model-specific component | |
| 7 | Rotor shaft | |
| Hammer Axle / Hammer Pin | ||
| Hammer pin retainer | Hammer pin end |
The EnduraHog Chip-Sizer CS covers 4 models: 30CS, 34CS, 45CS, 56CS. Former and renamed designations are listed in the models table on this page.
The EnduraHog Chip-Sizer CS is also documented under these designations: 30CS, 34CS, 45CS, 56CS.
The EnduraHog Chip-Sizer CS is listed under the Jeffrey Rader brand. Period: 2026. Status: Historical model.
8 components are recorded, including: Hammer / Swing Hammer, Hammer Axle / Hammer Pin, Rotor shaft, Impact Plate / Breaker Plate, Grate Bar, Side Housing Liner, Hammer pin retainer and more. The full list with locations is in the components table on this page.
Model-specific components with their own page: Hammer pin retainer (1 in total).
Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.
Submit an Enquiry