What other names or designations is the Canica MV successor modular VSI series known by?
The Canica MV successor modular VSI series is also documented under these designations: Canica MV2000, MV2000 Canica2000SD.
Modular VSI crushing plant · 2026-06 · 1 model


Select a model to jump to its component table; former and renamed designations are listed under “Historical names / renamings”.
| Model | Historical names / renamings | Period | Components |
|---|---|---|---|
| Canica MV successor modular VSI series | Canica MV2000; MV2000 Canica2000SD | 2026-06 | 29 |
The numbers on the diagram correspond one to one with the rows below.
| No. | Component | Location | Applies to |
|---|---|---|---|
| 1 | Feed chute | Red feed chute above the VSI | MV2000 |
| 2 | Canica 2000 VSI unit | Crusher in the centre of the module platform | MV2000 |
| 3 | Galvanized walkways, stairs, handrails and skid feet | Access structures and base support of the module | MV2000 |
| 4 | Ground-level lubrication unit | Lubrication unit at the lower right of the module | MV2000 |
| 5 | VSI drive motor | Black vertical drive motor beside the VSI | MV2000 |
| Component |
|---|
| Feed Tube — Feeding pipe |
| Anvil block or stone box |
| Ejection disc or enclosed rotor |
| Bearing Pedestal / Housing — Bearing support |
| MV2000 2021 drive motor and soft start |
| MV2000 2021 Lubricating Oil Tank |
| Bearing Pedestal / Housing — MV2000 2021 three-bearing support and Astralloy main shaft |
| MV2000 2021 cast chrome support protector |
| MV2000 2021 hopper rock cap and deflection plate |
| Feed Tube — MV2000 2021 external feeding pipe mechanism |
| Feed Tube — MV2000 2021 feeding pipe, cover and main frame liner |
| MV2000 2021 Flywheel with cast lining |
| MV2000 2021 Check Door Safety Lock |
| MV2000 2021 safety lock for opening cover |
| MV2000 2021 control panel |
| MV2000 2021 discharge chute and rubber dust cover |
| MV2000 2021 Lubrication motor/VSI motor/oil heater starting control |
| MV2000 2021 auxiliary electric control cabinet |
| MV2000 2021 emergency stop |
| MV2000 2021 automatic sequential start and stop and upstream and downstream interlocking |
| MV2000 2021 remote control interface |
| MV2000 2021 ammeter |
| MV2000 2021 removable switchgear panel (optional) |
| MV2000 2021 dual driver (optional) |
| MV2000 Hydralid hydraulic cap opening and capping mechanism |
| MV2000 off-site conveyor motor starting kit (optional) |
Models with the same components are grouped together; select a group to open its component table.
| No. | Component | Location |
|---|---|---|
| 1 | Feeding chute | Top of the body |
| 3 | MV2000 2021 Galvanized walkways, stairs, handrails and sliding seat feet | Modular steel structure |
| 4 | MV2000 2021 Floor Lubrication Unit | The bottom of the module is convenient for maintenance |
| Feed Tube — Feeding pipe | Above the rotor/disc | |
| Anvil block or stone box | Around the crushing chamber | |
| Ejection disc or enclosed rotor | Working part above the vertical shaft | |
| Bearing Pedestal / Housing — Bearing support | Vertical shaft support mechanism | |
| MV2000 2021 drive motor and soft start | VSI power system | |
| MV2000 2021 Lubricating Oil Tank | VSI oil lubrication system | |
| Bearing Pedestal / Housing — MV2000 2021 three-bearing support and Astralloy main shaft | VSI vertical shaft support; brand material name varies from material grade to | |
| MV2000 2021 cast chrome support protector | VSI bearing support exterior | |
| MV2000 2021 hopper rock cap and deflection plate | VSI top hopper | |
| Feed Tube — MV2000 2021 external feeding pipe mechanism | The hopper goes down to the top of the rotor | |
| Feed Tube — MV2000 2021 feeding pipe, cover and main frame liner | VSI upper part/inner body | |
| MV2000 2021 Flywheel with cast lining | VSI drive department | |
| MV2000 2021 Check Door Safety Lock | VSI body inspection door | |
| MV2000 2021 safety lock for opening cover | VSI cover opening mechanism | |
| MV2000 2021 control panel | Module electrical control bit | |
| MV2000 2021 discharge chute and rubber dust cover | Lower discharge of crusher | |
| MV2000 2021 Lubrication motor/VSI motor/oil heater starting control | Modular electric control cabinet | |
| MV2000 2021 auxiliary electric control cabinet | Module electrical | |
| MV2000 2021 emergency stop | Five modules; only the configurations listed in the 2021 volume | |
| MV2000 2021 automatic sequential start and stop and upstream and downstream interlocking | Module control | |
| MV2000 2021 remote control interface | Module control | |
| MV2000 2021 ammeter | Electronic control monitoring | |
| MV2000 2021 removable switchgear panel (optional) | Module electrical control interface | |
| MV2000 2021 dual driver (optional) | VSI driver configuration | |
| MV2000 Hydralid hydraulic cap opening and capping mechanism | VSI top cover and module operating platform | |
| MV2000 off-site conveyor motor starting kit (optional) | Electronic control interface of module to off-site feeding/finished product conveyor |
The Canica MV successor modular VSI series is also documented under these designations: Canica MV2000, MV2000 Canica2000SD.
The Canica MV successor modular VSI series is listed under the Canica-Jaques brand as: Modular VSI crushing plant. Period: 2026-06. Status: Historical model.
29 components are recorded, including: Feeding chute, Feed Tube, Anvil block or stone box, Ejection disc or enclosed rotor, Bearing Pedestal / Housing, MV2000 2021 drive motor and soft start, MV2000 2021 Lubricating Oil Tank, Bearing Pedestal / Housing and more. The full list with locations is in the components table on this page.
Model-specific components with their own page: MV2000 Hydralid hydraulic cap opening and capping mechanism, MV2000 off-site conveyor motor starting kit (optional) (2 in total).
Envoyez-nous un plan ou un échantillon et indiquez le modèle d'équipement et le nom de la pièce.
Provide the equipment model, drawing for engineering review and quotation. If service life or wear is a concern, describe the operating conditions as well.
Ou contactez-nous directement : +86 156 3797 3199
zzx@anranst.com
ANRANST provides customers worldwide with engineering assessment, production at certified foundries to drawing, quality control and finished-part delivery for custom wear parts and industrial spares, with scope to support other custom industrial parts.
Veuillez fournir la marque de l’équipement, le modèle complet et le numéro de série, le nom de la pièce, sa référence ou le numéro du plan, l’indice de révision du plan, la quantité, les exigences relatives au matériau et les conditions de service. Si ces identifiants ne sont pas disponibles, envoyez des photographies et les dimensions principales.
Submit an Enquiry